Torq Options Santa Cecilia Gold-Copper Project in Maricunga Belt in Chile
TSX.V: TORQ | OTCQX: TRBMF 600 – 1199 West Hastings Street, Vancouver, BC, Canada V6E 3T5
Torq Options Santa Cecilia Gold-Copper Project in Maricunga Belt in Chile
Vancouver, Canada – October 21, 2021 – Torq Resources Inc. (TSX-V: TORQ, OTCQX: TRBMF) (“Torq”
or the “Company”) is pleased to announce that it has acquired an option to earn a 100% interest in the
3,250-hectare (32.5 square kilometre (km)) Santa Cecilia gold-copper project, located approximately 100
km east of the city of Copiapo in northern Chile. The project is in the southern region of the world-class
Maricunga belt and immediately north of the El Indio belt (Figure 1). It is estimated that the Maricunga
belt could host up to 90 million ounces of gold endowment1. The belt is characterized by gold epithermal
and gold – copper porphyry deposits that are Oligocene - Miocene in age, including world-class multi-
million-ounce deposits such as Salares Norte, La Coipa, Cerro Maricunga, Marte, Lobo, La Pepa, El
Volcan, Caspiche and Cerro Casale (Figure 1).
The Santa Cecilia project is located immediately adjacent to the Norte Abierto project, held by Newmont
and Barrick , which is comprised of the Caspiche and Cerro Casale gold – copper porphyry deposits
(Figure 2). Collectively, these deposits contain proven and probable reserves of 23.2 million (M) ounces
of gold and 5.8 billion (B) pounds of copper and measured and indicated resources of 26.6 M ounces of
gold and 6.7 B pounds of copper2. Limited historical exploration work at Santa Cecilia was performed by
the previous operator, a major international mining company (“previous operator”), in 1988 – 1990, when
it drilled 47 holes, totaling approximately 14,000 metres (m), and completed 1,200 m of exploration tunnel
development that clearly defined epithermal gold and gold – silver mineralization as well as gold –
copper porphyry mineralization at surface and shallow depths , respectively. A subsequent operator of
Santa Cecilia then drilled two deeper holes in 2012 that successfully encountered gold – copper –
molybdenum porphyry mineralization underlying the shallow mineralization defined by the previous
operator’s drilling. Following this work, ground-based Quantec Orion 3D induced polarization and
magneto – telluric surveys were conducted to further define porphyry and epithermal targets across the
property, which remain untested.
A Message from Shawn Wallace, Executive Chair & Director:
“The Santa Cecilia gold-copper project represents the culmination of our acquisition strategy in Chile. It
is our belief that exploration at a project of this magnitude will be transformative for Torq. I would like to
thank our entire team, both here in Vancouver and on the ground in Chile, for all their contributions. We
look forward to unlocking the exploration potential of the property and adding long -term value for all
stakeholders, including surrounding communities, through their involvement in our progress as we earn
our social license by operating in a transparent, responsible and respectful manner.”
“Santa Cecilia completes an extraordinary exploration pipeline, which includes our Margarita iron-oxide-
copper-gold project, where drilling is ongoing, and the Andrea copper porphyry project, where exploration
is expected to commence in early 2022. Our premier portfolio provides the Company with great potential
to make Chile’s next significant copper-gold discovery.”
There are three primary target types associated with the 10 square km surficial hydrothermal alteration
footprint: 1) Surface epithermal disseminated oxide gold mineralization defined by the previous
operator’s shallow drilling, 2) High-grade gold-silver epithermal structures and veins, as observed in the
TSX.V: TORQ | OTCQX: TRBMF 600 – 1199 West Hastings Street, Vancouver, BC, Canada V6E 3T5
previous operator’s exploration tunnel and associated drilling, and 3) Underlying copper – gold –
molybdenum porphyry mineralization analogous to the Newmont/Barrick Caspiche and Cerro Casale
deposits, as defined by the 2011-2012 drill holes (Figure 3). (See disclosure regarding information from
previous operators, which has been reviewed by the Company)
A Message from Michael Henrichsen, Chief Geologist:
“Santa Cecilia represents an extraordinary opportunity for discovery in Chile. Effectively , it gives us the
rare ability to step back in time, to the early 1990’s, when the first round of discoveries were being made
within the Maricunga belt. The previous operator’s drilling has suggested a large oxide gold system and
the potential for high-grade precious metal structures, while the two holes in 2012 have demonstrated a
bona fide porphyry system beneath the near surface oxide mineralization. We are in an excellent position
to expand both the oxide and porphyry mineralized systems as well as to drill entirely new high quality
targets for the first time , which we believe have the potential to contribute to the discovery of a cluster
of mineralized porphyry bodies.”
A Message from Waldo Cuadra, General Manager, Chile:
“As an explorationist, to be able to identify, acquire and begin exploration at a project such as Santa
Cecilia, located within the gold-copper porphyry belt in Maricunga, is an exceptional event. Our group in
Chile has been pursuing this project for many years, and finally, with the full Torq Resources team, we
have been able to negotiate a favorable agreement. This is a significant milestone , and we very much
look forward to initiating exploration at a project we believe holds significant potential for the discovery
of a world-class gold-copper deposit.”
Near Surface Mineralization – Cerro del Medio Target:
The surface mapping, soil sampling, rock sampling and 14,000 m drill program completed by the previous
operator were primarily across the Cerro del Medio target area of the project and focused on identifying
shallow epithermal mineralization (Figure 3). Select highlights from the previous operator’s drilling
include 1.31 g/t gold equivalent (AuEq) over 34 m, 1.02 g/t AuEq over 22 m, 0.58 g/t AuEq over 162 m,
0.54 g/t AuEq over 132 m and 0.43 g/t AuEq over 256 m . Figure 4 illustrates a representative three -
dimensional view of the mineralization drilled by the previous operator. Additional results from that drill
program are presented in Table 1. Torq’s technical team considers these results to be significant as
they demonstrate the need for further drilling to potentially define a mineralized body at shallow depths.
The mineralization encountered in the drill holes is primarily oxide gold and gold – copper mineralization
from surface to depths of approximately 250 m. This ne ar surface mineralization is primarily
characterized by extensive zones of silica stockwork veining associated with hematite and jarosite as
well as minor silica – pyrite veins.
TSX.V: TORQ | OTCQX: TRBMF 600 – 1199 West Hastings Street, Vancouver, BC, Canada V6E 3T5
Table 1: Cerro del Medio Target – Drill Highlights from Previous Operator (1988 – 1990)
Hole ID From (m) To (m) Length (m) AuEq (g/t) Au (g/t) Cu (%) CuEq (%)
SP-SC-23
4 260 256 0.43 0.37 0.04 0.27
Incl. 136 146 10 0.75 0.66 0.05 0.47
and 252 254 2 28.05 28.00 0.03 17.72
SP-SC-24
138 300 162 0.58 0.36 0.14 0.37
Incl. 162 216 54 0.73 0.48 0.16 0.46
and 246 270 24 1.38 0.69 0.44 0.87
DDH-SC-04
142 160 18 4.02 2.09 1.22 2.54
Incl. 148 158 10 7.15 3.70 2.18 4.52
SP-SC-09
2 134 132 0.54 0.44 0.06 0.34
Incl. 6 12 6 0.75 0.72 0.02 0.47
and 26 60 34 1.31 1.09 0.14 0.83
SP-SC-14
84 250 166 0.40 0.29 0.07 0.25
Incl. 190 228 38 0.81 0.54 0.17 0.51
SP-SC-21
20 42 22 1.02 1.01 0.00 0.64
Incl. 34 36 2 10.01 10.00 0.01 6.32
166 300 134 0.41 0.31 0.06 0.26
Incl. 256 258 2 15.08 15.00 0.05 9.53
SP-SC-22 170 174 4.0 5.20 4.44 0.48 3.29
SP-SC-16
184 300 116 0.42 0.11 0.20 0.27
Incl. 192 228 36 0.65 0.07 0.37 0.41
and 268 300 32 0.54 0.14 0.25 0.34
DDH-SC-02
350 426 76 0.48 0.40 0.05 0.30
Incl. 306 312 6 0.55 0.42 0.08 0.34
and 392 394 2 10.03 9.94 0.06 6.34
DDH-SC-03
2 66 64 0.33 0.09 0.16 0.21
Incl. 44 60 16 0.53 0.15 0.24 0.33
78 309.5 231.5 0.29 0.20 0.06 0.18
Incl. 98 112 14 0.69 0.38 0.20 0.43
SP-SC-08
2 74.0 72.0 0.45 0.26 0.12 0.28
Incl. 2 38 36 0.50 0.28 0.14 0.32
and 44 64 20 0.56 0.34 0.14 0.35
80 250.0 170.0 0.31 0.24 0.04 0.19
Incl. 102 124 22 0.69 0.55 0.09 0.44
Main Interval - No less than 5 m of >= 0.1 g/t AuEq, maximum consecutive dilution 4 m;
Sub-interval - No less than 5 m of >= 0.3 g/t AuEq, maximum consecutive dilution 4 m;
Metal price used for Eq calculations: Au $1,300/oz, Cu $3/lb
TSX.V: TORQ | OTCQX: TRBMF 600 – 1199 West Hastings Street, Vancouver, BC, Canada V6E 3T5
High-Grade Structures and Veins – Vetas Condor Target:
The Vetas Condor high -grade gold – silver epithermal mineralization is encountered on the western
flanks of the Cerro del Medio target area where east -west trending quartz – alunite structures are
exposed over a 1 km by 350 m area (Figure 5). The previous operator completed a total of 1 ,100 m of
horizontal exploration tunnels that were oriented sub -parallel to parallel to the quartz -alunite ledges.
Evidently, crosscuts oriented perpendicular to the structures were not completed and therefore true width
of the high-grade mineralization was not determined.
The initial 200 m of the tunnel are oriented sub -parallel at a 20 -degree angle to the mapped quartz –
alunite structures. Highlighted intercepts from this section of the tunnel , while not true width ,
demonstrate the high-grade potential of the structures, and include 2.38 g/t gold and 101 g/t silver over
32 m and 0.66 g/t gold and 13.5 g/t silver over 134 m. In addition, approximately 436 m into the tunnel,
a high -grade vein sampled 58 g/t gold and 27 g/t silver over 2 m . Table 2 below summarizes the
significant intercepts in the exploration tunnel.
Table 2: Vetas Condor Target - Tunnel Assay Results from Previous Operator (1988 – 1990)
Hole ID From (m) To (m) Length (m) AuEq (g/t) Au (g/t) Ag (g/t) Cu (%)
T1-4LW 0 32 32 3.84 2.38 101.0 0.04
T1RW 0 36 36 1.26 0.60 42.1 0.05
TOE-LW
0 38 38 0.99 0.33 45.2 0.02
Incl. 0 14 14 1.45 0.24 86.7 0.01
and 20 22 2 1.67 1.20 32.0 0.02
and 28 38 10 1.17 0.62 37.8 0.02
45.2 147.2 102 0.43 0.20 8.3 0.07
Incl. 47.2 63.2 16 1.16 0.60 19.4 0.19
TOE-RW
21.2 155.2 134 1.04 0.66 13.5 0.12
Incl. 21.2 103.2 82 1.56 1.01 19.4 0.18
173.2 203.2 30 0.85 0.77 4.5 0.01
Incl. 185.2 193.2 8 2.29 2.19 6.3 0.01
TOE14-LW
156 164 8 0.94 0.53 28.3 0.01
Incl. 158 164 6 1.22 0.69 37.3 0.01
196 202 6 19.57 19.41 11.2 0.01
Incl. 196 198 2 58.38 58 27.0 0.01
Main Interval - No less than 5 m of >= 0.1 g/t AuEq, maximum consecutive dilution 4 m;
Sub-interval - No less than 5 m of >= 0.5 g/t AuEq, maximum consecutive dilution 4 m;
Metal price used for Eq calculations: Au $1,300/oz, Ag $18/oz, Cu $3/lb;
Hole ID – LW: Left wall; RW: Right wall
Torq’s technical team believes that the high-grade mineralization encountered in the tunnel has not been
adequately tested. There have only been three shallow drill holes testing the veins encountered in the
first 200 m of the exploration tunnel, which included 6.82 g/t gold and 16.8 g/t silver over 20 m at a depth
starting at 110 m (Figure 5) (true width unknown). Table 3 below summarizes drill results from the three
TSX.V: TORQ | OTCQX: TRBMF 600 – 1199 West Hastings Street, Vancouver, BC, Canada V6E 3T5
drill holes that tested below the tunnel. Torq plans to aggressively explore for high -grade gold – silver
mineralization along the 1 km long corridor defined by quartz - alunite structures.
Table 3: Vetas Condor Target - Drill Results from Previous Operator (1988 – 1990)
Hole ID From (m) To (m) Length (m) AuEq (g/t) Au (g/t) Ag (g/t)
DDH-SC-12
110 130 20 7.05 6.82 16.8
Incl. 112 114 2 56.7 55 121
SH-SC-06 60 68 8 1.75 0.82 67.3
SH-SC-07 20 24 4 3.84 3.60 17
Interval - No less than 5m of >= 0.1 g/t AuEq, maximum consecutive dilution 4m;
Metal price used for Eq calculations: Au $1,300/oz, Ag $18/oz
Underlying Porphyry Mineralization – Cerro Del Medio Target:
A two-hole drill program to test for porphyry mineralization beneath the epithermal mineralization
encountered in the previous operator’s drilling was conducted from January 2012 to May 2012. The two
holes were drilled from the northern side of the topographic high , defining the Cerro del Medio target
area, and both intersected hundreds of metres of gold – copper – molybdenum porphyry -style
mineralization (Figure 6). Drill hole CDM 03 intersected 0.45% CuEq over 925.7 m consisting of 0.21 g/t
gold, 0.27% copper and 82 ppm molybdenum, beneath the drilled gold mineralization from surface of
1.38 g/t gold over 24 m (drill hole SP -SC-24) by the previous operator in 1989 (Figure 7). This
demonstrates the potential for mineralization over one vertical kilometr e from surface that remains
open at depth and laterally. Table 4 below lists the intercepts from both drill holes.
Table 4: Cerro Del Medio Target - Underlying Porphyry Drill Results (January 2012 - May 2012)
Hole ID From (m) To (m) Length (m) CuEq (%) Au (g/t) Cu (%) Mo (ppm)
CDM-12-002 870 1,738.8 868.8 0.35 0.09 0.20 156
CDM-12-003 672 1,597.7 925.7 0.45 0.21 0.27 82
Interval - No less than 5 m of >= 0.1% CuEq, maximum consecutive dilution 4 m;
Metal price used for Eq calculations: Au $1,300/oz, Cu $3/lb, Mo $1/lb
Subsequent to the successful drill program testing for porphyry mineralization , ground-based Quantec
Orion-3D induced polarization (IP) and magneto -telluric surveys were conducted in November -
December of 2012 to characterize the geophysical signature of the underlying porphyry mineralization.
The encountered porphyry mineralization was characterized by very low resistivity values , measuring
between 3 – 6 ohm m, moderate chargeability values of less than 30 mrad and zones of very low
magnetic susceptibility (Figure 7). Critically, the survey shows an area of 2 km x 2 km x 1 km of low
resistivity values , which further demonstrates the potential to greatly expand the porphyry
mineralization encountered. Torq plans to further explore the porphyry system by targeting structural
corridors and potential feeder structures defined through the geophysical surveys.
High Priority Target Areas – Las Pircas – Pircas Norte:
To the east of the Cerro del Medio area , where the majority of the historical exploration work has been
conducted, are the Las Pircas and Pircas Norte target areas. These targets are located approximately 2
TSX.V: TORQ | OTCQX: TRBMF 600 – 1199 West Hastings Street, Vancouver, BC, Canada V6E 3T5
– 3 km from the Caspiche deposit and are defined by areas of strong epithermal silicification alteration,
which Torq’s technical team believes have significant potential for the discovery of underlying porphyry
mineralization (Figure 3). This is supported by the low resistivity and moderate chargeability geophysical
signatures, which start at depths as shallow as 250 m beneath the surface, as defined in the 2012 ground-
based Quantec IP and magneto -telluric surveys (Figure 8). Both targets are characterized by resistivity
lows of between 3 – 10 ohm m and moderate chargeability values of 30 – 40 mrad, which are consistent
with the geophysical responses associated with porphyry mineralization under the Cerro del Medio target
area. Together, these anomalies are approximately 1 km by 500 m, as defined by the resistivity data, but
remain open at depth (Figure 8). Historical soils show a gold – silver – copper – molybdenum anomaly
over the target areas coincident with the geophysical anomalies. The Las Pircas target area has only five
shallow historical drill holes, totaling 476 m, that did not intersect the geophysical anomalies, leaving
the target untested. The Pircas Norte target is under cover and has never been drill tested. Three rock
grab samples taken from a small, isolated outcrop within the target reported a best result of 1.4 g/t gold
and 0.5% copper associated with stockwork veining from a diorite porphyry exhibiting chlorite alteration
after secondary biotite. Torq plans to aggressively explore the Las Pircas and Pircas Norte target areas
with surficial programs to rapidly advance them to drill stage.
Option Terms:
Torq acquired the rights to explore the Santa Cecilia project via an option agreement that allows the
Company to acquire a 100% interest in the project, subject to net smelter return (NSR) royalties, through
cash payments (Table 5).
Table 5: Cash payments
Due Date Cash Payment (US$)
On signing definitive agreement $100,000
Within 12 months $300,000
Within 24 months -
Within 36 months $600,000
Within 48 months $1,000,000
Within 60 months $3,000,000
Within 72 months $5,000,000
Within 84 months $15,000,000
$25,000,000
The Company has also committed to the following work expenditures, which are scheduled from the date
it obtains the necessary permits to start its exploration campaigns, including the authorization from
indigenous communities located in the area of interest (Table 6).
TSX.V: TORQ | OTCQX: TRBMF 600 – 1199 West Hastings Street, Vancouver, BC, Canada V6E 3T5
Table 6: Work expenditures
Due Date Work expenditure (US$)
Within 12 months of obtaining permits $3,000,000
Within 24 months $4,500,000
Within 36 months $8,000,000
$15,500,000
The option agreement each includes an NSR of 3%, half of which is buyable once the option is executed
for a price that will be based on the fair value of the project , determined by mutual agreement between
the parties.
Figure 1: Illustrates the location of the Santa Cecilia project in the southern region of the world -class Maricunga belt , which
includes world-class multi-million-ounce deposits such as Salares Norte, La Coipa, Cerro Maricunga, Marte, Lobo, La Pepa, El
Volcan, Caspiche and Cerro Casale.
TSX.V: TORQ | OTCQX: TRBMF 600 – 1199 West Hastings Street, Vancouver, BC, Canada V6E 3T5
Figure 2: Illustrates the 10 square km hydrothermal alteration footprint of the Santa Cecilia project and its location relative to
the Norte Abierto project, held by Newmont and Barrick, which is characterized by the Caspiche and Cerro Casale gold – copper
porphyry deposits.