Infill Drilling at Arras Zone Within San Albino Intersects 30.27 G/T GOLD over 4.2 Meters (Estimated True Width) 2 Meters from Surface
1
595 Burrard Street, Suite 2833
Vancouver, BC V7X 1K8
Tel: (604) 646-1580
www.makominingcorp.com
TSX-V: MKO | OTCQB: MAKOF
May 6, 2020
PRESS RELEASE - #20-7
TSX-V: MKO; OTCQB: MAKOF
INFILL DRILLING AT ARRAS ZONE WITHIN SAN ALBINO INTERSECTS 30.27 g/t GOLD
OVER 4.2 METERS (ESTIMATED TRUE WIDTH) 2 METERS FROM SURFACE
Mako Mining Corp. (TSX-V: MKO; OTCQB: MAKOF) (“Mako” or the “Company”) is pleased to report positive
results from infill drilling at its wholly -owned San Albino gold project (“San Albino”) located in Nueva Segovia,
Nicaragua.
To date, 5,491.90 meters (“m”) of drilling in 134 diamond drill holes has been completed within the Arras Zone,
which is the area outlined by the C entral and Northeast pits in the Company’s preliminary economic assessment
(“PEA”), dated April 29, 2015 and available under the Company’s profile on SEDAR at www.sedar.com, with assays
reported for 28 of these holes in this press release (see attached map).
The 2019-20 drilling program targeting the Arras Zone was focused on identifying shallow mineralization that can
augment the initial phase of mining at the West pit. The Company followed a systematic approach of drilling shallow
holes every 20 m along strike and 20-40 m down dip. The results indicate a zone of approximately 80 m along strike
by 100 m down dip with grades and thickness that are variable within the zone. Importantly, the Arras Zone remains
open down dip with previous wide-spaced drilling intersecting the zone at over 600 m down dip.
The highlights of this press release are drill holes AR20 -162 and AR20 -166. Both holes were drilled to test
mineralization encountered in tunnel AR13 -TNL-03, which had a couple of channel samples of vein material that
assayed over 30 g/t Au. Drill hole AR20-162 tested the surface expression of the vein exposed in tunnel AR13-TNL-
03 and drill hole AR20-166 tested the same vein along the strike and down dip.
AR20-162 intersected 30.27 g/t Au and 31.2 g/t Ag over 5.5 m (4.2 m estimated true width) approximately 2 m from
surface (see attached cross section). This hole tested the surface expression of the vein encountered in tunnel AR13-
TNL-03. Results from AR20-162 indicate a similar grade approximately 10 m up dip over a wider interval.
AR20-166 was collared approximately 36 m north and down dip from AR20-162 and intersected a zone with an
estimated true thickness of 2.7 m approximately 1.5 m from surface . The mineralized zone encountered in AR20 -
166 had a total of five significant intercepts although the drill hole had poor recovery and possibly encountered
several historic workings. The two highest grade intercepts were 63.10 g/t Au and 46.4 g/t Ag over 2.15 m and 28.40
g/t Au and 33.3 g/t Ag over 1.0 m (see attached cross section).
Three Arras Zone holes from the 2019 -20 drilling program were previously released, highlighted by AR19 -115,
which intersected 24.18 g/t Au and 28.5 g/t Ag over 6.45 m (5.9 m e stimated true width) approximately 29 m from
surface (see attached longitudinal section and press release dated September 4, 2019).
A diamond drill rig along with a production drill rig will continue to identify additional shallow mineralization and
to quantify historic dumps along a previously tested ravine between the shallow and deeper portion of the Arras Zone
(see attached map). Results are pending from a total of 103 holes in the Arras Zone.
2
Mako is also pleased to report that mining at the West pit has recommenced after a six -week pause to implement
safety protocols due to the COVID-19 global pandemic. It is anticipated that mining will ramp up over the course of
the next few months.
Akiba Leisman, Chief Executive Officer of Mako states “it is rare in modern gold mining to intersect more than 30
g/t Au over four meters estimated true width and only a couple o f meters from surface. It is encouraging to see
positive results from drilling in the Arras Zone because the zone is not as well advanced as the zones within the West
pit, where the bulk of the infill program was focused last year, and where initial mining has recommenced. Today’s
results and those to follow have the potential of improving the already robust San Albino gold project by bringing in
high-grade and near surface ounces into the mine plan earlier than anticipated.”
History of the Arras Zone
Historic data indicates that the Arras Zone was discovered by the Spanish, with mining limited to superficial workings
where veins outcropped and formed the southern dip slope; this may partially explain the sporadic continuity in the
shallow drill holes.
A review of a 1948 report by Roger Peale indicates that the Arras Zone was one of the last areas mined at San Albino.
The area is described as being in production as late as 1943 and with several shoots extending 30 m along strike and
20 m down dip. Overall, the Arras Zone is described as having a strike extent of 200 m and dip of 60 m and average
width of 1.6 m. Subvertical and low angle faults are described to have offset the veins.
2019-20 Infill Drilling Program Assay Results Reported in this Press Release
Drill Hole From
(m)
To
(m)
Width
(m)
Au
(g/t)
Ag
(g/t) Interval Average/Comments True Width
(m)**
AR19-117
to 120 No significant results
AR19-121 79.00 80.00 1.00 1.57* 4.3 1.57 g/t Au and 4.3 g/t Ag over 1.0 m 0.5
AR19-122 No significant results
AR19-123 46.50 47.20 0.70 7.26* 16.6 7.26 g/t Au and 16.6 g/t Ag over 0.7 m 0.6
AR19-124 81.40 82.00 0.60 Void
AR19-125
28.50 30.00 1.50 3.67* 8.7
4.83 g/t Au and 11.8 g/t Ag over 4.7 m 4.4
30.00 31.50 1.50 1.61* 3.4
31.50 32.50 1.00 9.41* 23.8
32.50 33.20 0.70 7.69* 19.1
AR19-126
23.00 24.00 1.00 2.12* 35.9 2.12 g/t Au and 35.9 g/t Ag over 1.0 m 1.0
31.00 32.50 1.50 2.69* 4.7 2.69 g/t Au and 4.7 g/t Ag over 1.5 m 1.5
35.45 38.35 2.90 Void
AR19-127
11.40 24.00 12.60 Void and Muck
20.50 21.50 1.00 6.42 22.8 Muck
AR19-128
15.50 16.50 1.00 1.13 0.8 1.13 g/t Au and 0.8 g/t Ag over 1.0 m 0.8
17.50 19.10 1.60 Void
19.10 20.00 0.90 0.57* 3.7
Muck 20.00 21.00 1.00 0.03 1.9
21.00 22.50 1.50 0.80 12.7
22.50 23.50 1.00 3.79* 20.4 5.77 g/t Au and 18.6 g/t Ag over 2.0 m 1.5
3
23.50 24.50 1.00 7.74* 16.8
AR19-129 17.60 19.80 2.20 Void
AR19-130
24.50 25.60 1.10 1.46* 8.5
3.86 g/t Au and 14.2 g/t Ag over 4.5 m 4.4
25.60 26.60 1.00 10.99* 25.2
26.60 27.60 1.00 3.33* 11.5
27.60 29.00 1.40 1.03* 12.8
AR19-131
19.10 20.10 1.00 37.66* 16.0 37.66 g/t Au and 16.0 g/t Ag over 1.0 m 0.9
75.80 76.80 1.00 5.61* 14.2 5.61 g/t Au and 14.2 g/t Ag over 1.0 m 0.9
AR19-132
18.00 19.50 1.50 1.01* 2.3
1.66 g/t Au and 3.3 g/t Ag over 3.0 m 2.5
19.50 21.00 1.50 2.32* 4.2
AR19-133 Results pending
AR19-134 12.00 12.50 0.50 79.47* 67.5 79.47 g/t Au and 67.5 g/t Ag over 0.5 m 0.25
AR19-135
34.20 35.20 1.00 2.71* 12.9
17.12 g/t Au and 26.7 g/t Ag over 3 m 1.7 35.20 36.20 1.00 5.66* 9.3
36.20 37.20 1.00 42.99* 57.9
AR19-136
to 150 Results pending
AR19-151 24.50 25.50 1.00 2.03 8.7 2.02 g/t Au and 8.7 g/t Ag over 1.0 m 0.6
AR19-152
to 155 Results pending
AR19-156 8.40 9.10 0.70 26.20 34.5 26.20 g/t Au and 34.5 g/t Ag over 0.7 m 0.7
AR19-157 Results pending
AR19-158
14.80 16.00 1.20 23.80 53.7 23.80 g/t Au and 53.7 g/t Ag over 1.2 m 0.6
17.50 18.00 0.50 7.10 24.0 7.10 g/t Au and 24.0 g/t Ag over 0.5 m 0.3
AR20-159
to 161 Results pending
AR20-162
9.00 10.00 1.00 5.50 18.1
30.27 g/t Au and 31.2 g/t Ag over 5.5 m 4.2
10.00 10.70 0.70 0.49 5.2
10.70 11.20 0.50 22.30 31.0
11.20 11.90 0.70 164.70 98.0
11.90 13.00 1.10 19.00 27.0
13.00 13.50 0.50 4.83 4.4
13.50 14.50 1.00 10.90 34.0
AR20-163
to 164 Results pending
AR20-165
0.00 1.30 1.30 8.62 21.8
Overburden
1.30 2.30 1.00 1.34 7.3
2.30 3.30 1.00 3.69 6.8
7.16 g/t Au and 23.37 g/t Ag over 3.0 m 2.8 3.30 4.30 1.00 10.50 33.9
4.30 5.30 1.00 7.29 29.4
AR20-166
0.00 1.50 1.50 2.92 11.3
Overburden
1.50 3.10 1.60 11.30 26.7
3.10 6.60 3.50 Void
4
6.60 7.10 0.50 3.26 7.6 3.26 g/t Au and 7.6 g/t Ag over 0.5 m 0.3
8.85 9.65 0.80 3.40 9.2 3.40 g/t Au and 9.2 g/t Ag over 0.8 m
2.7 (including
voids)
9.65 12.35 Void
12.35 13.80 1.45 2.42 8.9 2.42 g/t Au and 8.9 g/t Ag over 1.45 m
13.80 17.80 Void
18.30 20.45 2.15 63.10 46.4 63.10 g/t Au and 46.4 g/t Ag over 2.15 m
20.45 22.45 Void
22.45 23.45 1.00 28.40 33.3 28.40 g/t Au and 33.3 g/t Ag over 1.0 m
AR20-167
to 171 Results pending
AR20-172
11.90 12.50 0.60 9.20 16.6 9.20 g/t Au and 16.6 g/t Ag over 0.6 m 0.5
12.50 15.10 2.60 Void
15.10 15.60 0.50 2.00 3.6 Muck
AR20-173
to 176 Results pending
AR20-177
0.00 1.00 1.00 1.86 4.0 Overburden
3.20 4.20 1.00 5.11 31.8 5.11 g/t Au and 31.8 g/t Ag over 1.0 m 0.9
AR20-178
to 181 0.30 0.70 0.40 Results pending
AR20-182
7.80 8.50 0.70 7.08 30.6
9.42 g/t Au and 15.9 g/t Ag over 2.7 m 2.5 8.50 9.50 1.00 0.08 2.5
9.50 10.50 1.00 20.40 19.0
AR20-183
to 198 Results pending
AR20-199 2.00 3.00 1.00 1.11 3.3 1.11 g/t Au and 3.3 g/t Ag over 1.0 m 0.9
AR20-200
to 247 Results pending
The mineralized intervals shown above utilize a 1.0 g/t gold cut-off grade with not more than 1 .0 meter of internal
dilution. * Indicates use of metallic screening method for assays. ** True width is estimated from interpreted sections.
5
6
7
Sampling, Assaying, QA/QC and Data Verification
Drill core was continuously sampled from inception to termination of the drill hole. Sample intervals were typically
one meter. Drill core diameter was HQ (6.35 centimeters). Geologic and geotechnical data was captured into a
digital database, core was photographed, then one -half split of the core was collected for analysis and one -half was
retained in the core library. Samples were kept in a secured logging and storage facility until such time that they
were delivered to the Managua facilities of Bureau Veritas and pulps were sent to the Bureau Veritas laboratory in
Vancouver for analysis. Gold was analyzed by standard fire assay fusion, 30gram aliquot, AAS finish. Samples
returning over 10.0 g/t gold are analyzed utilizing standard Fire Assay-Gravimetric method. Due to the presence of
coarse gold, the Company has used 500-gram metallic screened gold assays for analyzing samples from mineralized
veins and samples immediately above and below drilled veins. This method, which analyzes a larger sample, can be
more precise in high-grade vein systems containing coarse gold. All reported drill results in this press release used
the standard Fire Assay-Gravimetric method unless otherwise indicated as using the metallic screening method. The
Company follows industry standards in its QA&QC procedures. Control samples consisting of duplicates, standards,
and blanks were inserted into the sample stream at a ratio of 1 control sample per every 10 samples. Analytical results
of control samples confirmed reliability of the assay data.
Qualified Person
8
John M. Kowalchuk, P.Geo, a geologist and qualified person (as defined under National Instrument 43-101) has read
and approved the technical information contained in t his press release. Mr. Kowalchuk is a senior geologist and a
consultant to the Company.
On behalf of the Board,
Akiba Leisman
CEO
About Mako
Mako Mining Corp. is a publicly listed gold mining, development and exploration firm. The Company is developing
its high-grade San Albino gold project in Nueva Segovia, Nicaragua. Mako’s primary objective is to bring San Albino
into production quickly and efficiently, while continuing exploration of prospective targets in Nicaragua.
For further information: Mako Mining Corp., Akiba Leisman, Chief Executive Officer, Telephone: 203-862-7059,
E-mail: [email protected] or visit our website at www.makominingcorp.com and SEDAR
www.sedar.com.
Forward-Looking Statements: Statements contained herein, other than of historical fact, may be considered “forward-looking
information” within the meaning of applicable securities laws. Forward -looking information is based on certain expectations
and assumptions, including that the Company’s exploration and in -fill drilling programs including at the Arras Zone, will be
successfully completed; that mineralization discovered at the Central and Northeast pits will augment the initial phase of mining
at the West pit; that the Company will be able to identify additional shallow mineralization and to quantify historic dumps along
the previously tested ridgeline between the Central and Northeast pits and the West Pit; that any outstanding assay results ,
including from the Arras Zone, will be as anticipated; that the mineralization discovered is anticipated to have a material impact
on the economics of the San Albino gold project; that the Company will be able to successfully adjust its mine plan based on
anticipated successful drilling results from the Arras Zone, and bring in high-grade and near surface ounces into the mine plan
earlier than anticipated ; that the geological model will continue to yield highly predicable results and that mining at the West
pit will ramp up over the course of the next few months and such other risk factors as outlined in the continuous disclosure
documents of the Company filed on SEDAR at www.sedar.com. Such forward-looking information is subject to a variety of risks
and uncertainties which could cause actual events or results to differ ma terially from those reflected in the forward -looking
information, including, without limitation, the risks that additional satisfactory exploration and drilling results at the Arras Zone
at San Albino will not be obtained; that the Company will not be able to augment its initial phase of mining at the West pit as a
result of mineralization discovered at the Central and Northeast pits ; that the PEA is preliminary in nature and there is no
certainty that the PEA will be realized; the risk of economic and/or t echnical failure at the San Albino project associated with
basing a production decision on the PEA without demonstrated economic and technical viability; that exploration results will
not translate into the discovery of an economically viable deposit; risks and uncertainties relating to political risks involving the
Company’s exploration and development of mineral properties interests; the inherent uncertainty of cost estimates and the
potential for unexpected costs and expense; commodity price fluctuations , the inability or failure to obtain adequate financing
on a timely basis and other risks and uncertainties. Such information contained herein represents management’s best judgment
as of the date hereof, based on information currently available and is incl uded for the purposes of providing investors with the
Company’s plans and expectations at its San Albino project and may not be appropriate for other purposes. Mako does not
undertake to update any forward-looking information, except in accordance with applicable securities laws.
Neither the TSX Venture Exchange nor its Regulation Services Provider (as that term is defined in the policies of the TSX Venture
Exchange) accepts responsibility for the adequacy or accuracy of this release.