US$1.25 for zinc (“Zn”), and US$1.05 for lead (“Pb”), with assumed mill recoveries of 85% for Au, 80% for Ag, 82 % for Cu and Pb, and 77% for Zn. Lupaka Samples 9.22 g/t Au-Eq. Over A Strike Length of 130 m from the Newly Developed 3430 Sublevel at Invicta
* Au-Eq. calculations are based on US$1250 for gold (“Au”), US$17.00 for silver (“Ag”), US$3.00 for copper (“Cu”),
US$1.25 for zinc (“Zn”), and US$1.05 for lead (“Pb”), with assumed mill recoveries of 85% for Au, 80% for Ag, 82 % for
Cu and Pb, and 77% for Zn.
Lupaka Samples 9.22 g/t Au-Eq. Over A Strike Length of 130 m
from the Newly Developed 3430 Sublevel at Invicta
VANCOUVER, BRITISH COLUMBIA, June 07, 2018 -- Lupaka Gold Corp. (" Lupaka
Gold" or the “ Company") (TSX-V: LPK, FRA: LQP) is pleased to announce the results
from a recent systematic underground sampling program on the newly developed 3430
production sublevel, located 30 metres up-dip of the 3400 Level, at the Company’s 100%
owned Invicta Gold Development Project (“Invicta Project” or “Invicta”).
Sampling Program Highlights:
• Sample assay values from the Atenea vein on the 3430 sublevel averaged
9.22 grams per tonne (“g/t”) gold equivalent1 (“Au-Eq.”) over a strike length
of 130 metres (“m”), with an average sample width of 4.2 m
• Average grade of 9.22 g/t Au-Eq. is higher than the estimated grade of 8.12
g/t Au-Eq. within the block model of the sampled area on the 3430 sublevel
and appears consistent with the 9.86 g/t Au-Eq. sampled on the 3400 Level
(see news release dated March 15, 2018)
• Geological mapping shows that the hanging wall split has merged with the
footwall zone on the 3430 sublevel, which could potentially result in more
efficient mining and lower dilution than the assumptions in the PEA
• Development on the 3430 sublevel, including the crosscuts, plus geological
mapping and sample assay values demonstrate horizontal widths ranging
from 4 m up to 12 m for the Atenea vein on the 3430 sublevel
Development Highlights:
• Approximately 235 m of horizontal development, including 5 cross-cuts, has
been completed on the 3430 sublevel, ending in mineralization on the
eastern face
• Vent raise from 3400 Level to 3430 sublevel has been completed ventilation
circuit established
“Results from the underground sampling program on the newly constructed 3430 sublevel
are very encouraging and demonstrates the continuity of the Atenea mineralization both
up-dip from the 3400 Level and along strike. Having learned the hanging wall split merges
with the footwall zone is an important geological discovery and provides an opportunity to
improve on our conceptual mine development costs and dilution assumptions in the PEA.
With sampled grades from the 3430 sublevel coming in higher than within our Mineral
Resource block model from the same area , we remain well positioned for the
commencement of mine production in the third quarter of this year.”
Will Ansley, President and CEO of Lupaka
2
Development of 3430 Sublevel & Sampling Program Results
Development on the newly constructed 3430 sublevel was initiated in preparation for the
first block of mining production (located between the 3400 Level and the 3430 sublevel),
scheduled to commence in the third quarter of 2018 (“ Q3 2018”). Subsequent to cross-
cutting the Atenea vein, lateral development preceded southeast and southwest over
approximately 235 m, including the creation of four additional cross-cuts (see plan in
Appendix A) , ending in mineralization on the eastern face. The 3430 sublevel
development also provided an opportunity to demonstrate the vertical and horizontal
continuity of the Atenea vein and to compare the sampled grades with the current Mineral
Resource block model, as well as the mineralization contained on the 3400 Level, located
30 metres below.
Consistent with the comprehensive sampling program undertaken on the 3400 Level (see
plan shown in Appendix B), underground channel sampling was systematically performed
on the 3430 sublevel over the width of the development (3.5 m wide by 3.0 metres wide)
at intervals of approximately every 5 m (consistent with the size of the Mineral Resource
block model), as well as over the five cross-cuts.
The polymetallic mineralization within the At enea vein is hosted by structurally defined
components which were mapped and sampled . Summarized assay sample results are
tabulated and presented in Table 1, and a detailed sampling map is provided in Appendix
A.
Table 1: Average Sampling Results from 3430 Sublevel Atenea Vein Sampling Program
3430 Level Length
Metres
Width
Metres
Au
g/t
Ag
g/t
Cu
%
Pb
%
Zn
%
Au-Eq.
g/t
Atenea Vein 130.00 4.2 4.31 59.21 1.68 1.33 1.26 9.22
Overall, the sample results were found to be consistent with sample results from
the 3400 Level located 30 m below, however, the average sampled grade of 9.22 g/t
Au-Eq. is higher than the estimated grade of 8. 12 g/t Au-Eq. contained within the
Mineral Resource block model from the sampled area. Importantly, the geological
mapping on the 3430 sublevel showed that the hanging wall split vein, as seen on
the 3400 Level, has merged with the footwall zone. The continuation of the hanging
wall split and the footwall zone through the 3430 sublevel was assumed in the
Mineral Resource model and in the PEA conceptual mine plan. The merger of these
zones cou ld potentially result in more efficient mining and lower dilution upon
extraction of the mineralized material (due to the absence of non -mineralized
material in between the two zones).
Although the average sampled width of the Atenea vein on the 3430 sublevel was 4.2 m,
compared to approximately 6.0 m on the 3400 Level, sampling on the 3430 sublevel was
restricted by smaller development headings (3.5 m wide), as well as fewer cross-cuts (5)
compared with the 3400 Level (7). Geological mapping and sampling over the 5 cross -
cuts on the 3430 sublevel demonstrates an estimated horizontal width of the Atenea vein
ranging from 4 m up to 12 m. It is anticipated that the average horizontal width on 3430
sublevel will be in-line, or possibly exceed, the average conceptual mining width of 8.0 m,
as estimated in the PEA conceptual mine plan.
Summary results obtained from 205 samples taken in the drift and crosscuts, over spacing
of approximately every 5 m, are tabulated in Table 2.
3
Table 2: Summary Assays from 3430 Level – Atenea Vein
Width
metres
Au Ag Cu Pb Zn Au-Eq.
g/t g/t % % % g/t
1.70 0.47 12.53 0.34 1.56 1.01 2.64
2.50 34.79 42.40 0.92 1.94 2.22 39.19
2.40 1.11 16.96 0.79 0.52 0.38 3.09
3.35 0.87 9.51 0.58 0.21 0.28 2.19
3.45 2.02 12.57 0.60 0.22 0.46 3.54
3.30 2.57 18.52 0.91 0.06 0.08 4.34
3.40 1.46 73.82 1.90 0.15 0.25 5.65
3.30 1.36 17.50 0.87 0.16 0.06 3.09
5.90 2.57 37.47 1.78 0.14 0.09 6.01
5.12 2.96 22.36 0.75 1.00 1.51 5.89
4.40 0.92 38.95 1.11 0.70 0.94 4.12
4.00 0.72 47.38 1.94 3.07 2.41 7.56
3.90 0.60 55.05 1.66 4.02 3.64 8.33
4.00 2.87 37.50 1.55 1.17 1.03 7.06
3.50 6.46 42.29 1.21 1.02 0.51 9.80
10.50 4.62 47.24 1.56 1.80 1.95 9.86
3.30 1.52 25.73 0.83 0.60 0.66 3.90
3.50 1.16 39.77 1.39 2.12 3.49 7.13
3.20 1.64 62.88 1.94 3.45 3.41 9.47
5.75 3.78 59.04 1.93 2.93 4.10 11.68
3.50 2.15 55.60 1.78 3.29 2.69 9.12
7.30 4.24 48.38 1.49 1.58 1.78 9.16
3.42 4.89 42.19 1.61 1.56 2.26 10.21
4.40 5.21 39.09 1.04 1.68 1.83 9.39
3.40 3.81 63.06 1.90 1.17 0.78 8.76
3.46 4.15 54.99 2.47 0.97 0.85 9.82
3.50 5.06 46.74 0.93 0.70 1.17 8.21
9.30 5.45 95.27 2.41 0.35 0.26 10.85
3.30 10.40 149.88 3.56 1.00 0.56 18.86
9.40 3.85 97.96 2.74 1.39 0.74 10.66
4.10 3.45 76.80 1.38 1.10 0.58 7.59
3.80 7.99 146.11 3.31 1.61 0.84 16.51
3.80 3.25 50.39 1.41 1.02 0.62 7.07
3.35 5.17 77.46 2.04 1.16 1.13 10.72
3.30 3.34 149.27 2.67 2.09 1.17 11.35
2.40 19.81 94.92 2.25 0.84 0.29 25.23
3.50 7.93 105.64 2.36 1.10 0.35 13.86
3.30 1.06 56.58 0.66 0.52 0.02 3.14
Weighted
Averages 4.20 4.31 59.21 1.68 1.33 1.26 9.22
Total Length
(metres) 130
4
Project Background
Lupaka’s Invicta Gold Project is a polymetallic development project located approximately
120 kilometres north of Lima, Peru. On May 11, 2018 a PEA was completed on the project
by SRK Consulting (Canada) Inc. which evaluated the economic potential of the
underground extraction of the Indicated and Inferred Mineral Resources from the Atenea
Vein close to the existing 3400 Level adit (up to 130 m above the 3400 Level) utilizing a
sublevel long -hole, open stoping mining method supported by initial toll treatment
processing options. Highlights of the PEA are summarized below:
• Mineral Resource Statement of 3.0 million tonnes of Indicated Mineral
Resources at 5.78 g/t Au-Eq. using a 3. 0 g/t Au-Eq. cut-off, and 0.6 million
tonnes of Inferred Mineral Resources at 5.29 g/t Au-Eq.
• Initial 6-year mine plan (underground) designed on a portion of th e Mineral
Resource utilizing the existing infrastructure and minimizing capital start-up
costs
• Sublevel open stope mining producing ~ 670,000 tonnes of mineralized
material at 8.6 g/t Au -Eq.* with production of ~ 185,000 Au -Eq. oz (within
initial 6-year mine plan)
• Average annual pre-tax cash flows of US$10.2 million, average annual after-
tax cash flow of US$8.2 million
• Annual production of 33,700 Au-Eq. oz, during steady state
• Annual payable metal of 26,700 Au-Eq. oz, during steady state
• All-in Sustaining Costs of US$575 Au -Eq. oz over initial 6 -year mine life,
average annual pre-tax operating profit of US$12.3 million
• Pre-tax 5% NPV of US$53.6 million
• Low capital investment: US$4.3 million in pre -production capital with a
payback of less than one year
The PEA considers only part of the reported Mineral Resource (the Atenea Vein close to
existing infrastructure) with the objective of generating positive cash flow from a low-cost
operation while simultaneously re -investing in and further evaluating the deposit to
potentially expand production in the future.
Quality Control and Assurance
The analyses for this sampling campaign were carried out by ALS, an accredited
laboratory, in Lima, Peru, exercising a thorough Quality Assurance and Control program
(QA/QC). As part of QA/QC protocol, duplicates, standards and blanks were inserted into
the sample processing stream. The sample locations were mapp ed, surveyed and
photographed for reference. Individual sample channels vary between 0. 2 to 2.5 metres
wide. Samples were bagged, sealed and delivered to the ALS sample preparation facility
in Lima , Peru. Gold was assayed by a 50-gram fire assay and re -assayed for the
overlimits, with an AAS finish. All ALS labs are ISO 9000 registered.
Technical Report
Further information about the PEA and the resource estimate referenced in this news
release, including data verification, key assumptions, parameters, risks and other factors,
are provided in the technical report prepared following Canadian Securities Administrators’
National Instrument (NI) 43-101 and Form 43 -101F1 guidelines for the Invicta Project
5
dated May 11, 2018 , and is available under the Company profile on SEDAR
(www.sedar.com).
Neither the TSX Venture Exchange nor its Regulation Service Provider (as the term
is defined in the policies of the TSX Venture Exchange) accepts responsibi lity for
the adequacy of this news release.
About Lupaka Gold
Lupaka is an active Canadian-based company focused on creating shareholder value
through discoveries and strategic development of its assets in some of the most prolific
mining regions of Peru.
Invicta Gold Development Project – 100% owned, the Company’s flagship project is an
advanced stage gold-copper polymetallic underground deposit located approximately 120
kilometres north of Lima. Over $12 million of capital has been spent by previous owners
on development and infrastructure at Invicta , and m anagement expects to commence
potential production in the second half of 2018 by using third-party mining contractors and
utilizing the existing adit and workings. The Invicta project is fully permitted and community
agreements are in place.
The potential underground operation will be focused on underground extraction of
Indicated Mineral Resources and Inferred Mineral Resources from the Atenea vein within
close proximity to the existing 3400 Level adit (up to 130 metres above the 3400 Level).
Invicta’s approved EIA allows for mine production of up to 1,000 tpd, although the current
conceptual mining plan is targeting 350 tpd.
Cautionary Note Regarding the Invicta Production Decision
The PEA is preliminary in nature and includes Inferred Mineral Resources that are
considered too speculative geologically to have the economic considerations applied to
them that would enable them to be categorized as mineral reserves and there is no
certainty that the PEA will be realized. Mineral resources that are not mineral reserves do
not have demonstrated economic viability. The estimate of mineral resources may be
materially affected by envi ronmental, permitting, legal, title, taxation, socio -political,
marketing, or other relevant issues. The quantity and grade of reported inferred resources
referred to in the PEA are uncertain in nature and there has been insufficient exploration
to define these inferred resources as an indicated or measured mineral resource category.
It is important to note while a mine production decision has been made by the Company,
that the information provided in this news release is preliminary in nature. There is no
certainty that a potential mine will be realized. A mine production decision that is not based
on a feasibility study demonstrating economic and technical viability does not provide
adequate disclosure of the increased uncertainty and specific economic an d technical
risks of failure associated with such a production decision.
About SRK Consulting (Canada) Inc.
SRK Consulting (Canada) Inc. form part of the SRK Consulting Group which is an
independent, international consulting company that provides focused advice and solutions
to clients, mainly from earth and water resource industries. Formed in 1974, SRK now
employs more than 1,400 professionals in over 40 offices on 6 continents. Among SRK's
6
1,500 clients are most of the world's major- and medium-sized metal and industrial mineral
mining houses, exploration companies, banks, petroleum exploration companies,
construction firms and government departments.
FOR FURTHER INFORMATION PLEASE CONTACT:
Will Ansley, President & C.E.O.
Tel: (416) 862-5257
or visit the Company’s profile at www.sedar.com or its website at www.lupakagold.com
Qualified Person
The technical information in this document has been reviewed and approved by Julio
Castañeda Mondragón - MAIG, the President of Lupaka Gold Peru S.A.C. , a Peruvian
subsidiary of the Company, and a Qualified Person as defined by National Instrument 43-
101. Mr. Castañeda has verified the scientific and technical information, including
sampling, analytical and test data underlying the information or opinions contained in this
news release.
Cautionary Statements Regarding Forward Looking Information
This press release contains forward -looking statements which constitute "forward -looking
information" within the meaning of applicable securities laws, including all statements, trend
analysis and other information relative to anticipated future events or results. All statements, other
than statements of historical fact, included herein are considered forward -looking statements,
including, without limitation, statements relating to: any benefit to development costs and
improvement in mine dilution from the merger of the hanging wall split and the footwall zone; the
commencement of potential production from the Invicta Project in Q3 2018, the targeted mining
rate of 350 tpd, anticipated methods of production and the generation of cash therefrom.
Forward-looking statements are based on assumptions, estimates and opinions of management at
the date the statements are made and which the Company believes are reasonable. Such
information involves risks and uncertainties, and undue reliance should not be placed on s uch
information, as unknown or unpredictable factors could have material adverse effects on future
results, performance or achievements of the Company. Among the key factors that could cause
actual results to differ materially from those projected in the f orward-looking information are the
following: that the repayment of the PLI Financing is consummated on the anticipated terms; that
the Company will not experience any material accident, labour dispute, shortage of skilled and
professional staff, changes in project plans, equipment availability and failures, process failures,
the ability of third party service providers to deliver services on reasonable terms and in a timely
manner; future exploration activities planned at the Invicta Gold Project, and the timing and results
thereof; market conditions and general business, economic, competitive, political and social
conditions and with respect to the planned mining operations at Invicta; that pre -production mine
development can be completed in the time and for the cost projected; that the Company will be
able to obtain funding for planned production expenses; that mineralization at Invicta will be of the
grades and in the locations expected; that the Company will be able to extract and transport
mineralized rock efficiently and sell the mineralized rock at the prices and in the manner recoveries
and quantities expected; that permits will be received on the terms and timeline expected and that
other regulatory or permitting issues will not arise; that mining methods and reclamation can be
employed in the manner and at the costs expected and that such methods yield the results the
Company expects them to. Forward-looking information involves known and unknown risks,
uncertainties and other factors which may cau se the actual results, performance or achievements
of the Company to be materially different from any future results, performance or achievements
expressed or implied by the forward-looking information. Such risks, uncertainties and other factors
include, among others: all of the risks described in this news release; that the Company will not be
able to comply with the delivery or other obligations in the PLI Financing Agreement and the risk
that PLI will enforce its security over the Company’s assets, inc luding its mineral properties;
7
changes in commodity prices; currency exchange rates (such as the Canadian dollar versus the
United States dollar); risks associated with dilution; labour and employment matters; risks in the
event of a potential conflict of interest; changes in general economic, business and political
conditions, including changes in the financial markets; changes in applicable laws; and compliance
with extensive government regulation; and other risks generally associated with mineral
exploration. This forward -looking information may be affected by risks and uncertainties in the
regular course of business and due to market conditions. Additional risks are described in the
Company’s annual information form, which is available on SEDAR at www.sedar.com.
Although the Company has attempted to identify important factors that could cause actual actions,
events or results to differ materially from those described in forward-looking information, there may
be other factors that cause actions, events or results to not be as anticipated, estimated or intended.
There can be no assurance that forward -looking information will prove to be accurate, as actual
results and future events could differ materially from those anticipated in such statements. Readers
are cautioned not to place undue reliance on forward -looking information due to the inherent
uncertainty thereof. Lupaka Gold does not undertake any obligation to update forward -looking
statements except as required by applicable securities laws. Investor s should not place undue
reliance on forward-looking statements.
* Au-Eq. calculations are based on US$1250 for gold (“Au”), US$17.00 for silver (“Ag”), US$3.00 for copper (“Cu”), US$1.25 for zinc (“Zn”), and US$1.05 for lead (“Pb”), with assumed mill recoveries
of 85% for Au, 80% for Ag, 82 % for Cu and Pb, and 77% for Zn.
APPENDIX A
Summarized Assay Results from Underground Channel Sampling of the Atenea Vein on 3430 Sublevel, Invicta Gold Mine