LIFT Intersects 14 m at 1.24% Li2O at the BIG East Pegmatite, Yellowknife Lithium Project, NWT
LIFT Intersects 14 m at 1.24% Li2O at the BIG
East Pegmatite, Yellowknife Lithium Project,
NWT
Vancouver, British Columbia--(Newsfile Corp. - September 26, 2023) - Li-FT Power Ltd. (
CSE: LIFT
)
(
OTCQX: LIFFF
) (
FSE:
WS0
) ("
LIFT
" or the "
Company
") is pleased to report assays from 5 drill holes
completed at the Fi Southwest, Shorty, and BIG East pegmatites within the Yellowknife Lithium Project
("YLP") located outside the city of Yellowknife, Northwest Territories (Figure 1). Drilling has intersected
significant intervals of spodumene mineralization, with the following highlights:
Highlights:
YLP0037:
33 m at 0.71% Li
2
O,
including 13 m at 1.13% Li
2
O (Fi Southwest)
YLP0040:
8 m at 1.26% Li
2
O
, (Shorty)
YLP0043:
13.67 m at 1.22% Li
2
O
, including 7 m at 1.64% Li
2
O and (BIG East)
and:
11 m at 0.84% Li
2
O
and:
14 m at 1.24% Li
2
O.
YLP0047:
16 m at 0.94% Li
2
O
, including 12 m at 1.15% Li
2
O (Fi Southwest)
Discussion of Drill Results
Drill hole YLP0037 intercepted 33 metres of 0.71% Li
2
O of the Fi Southwest pegmatite from 55 metres.
Within that interval from 60 metres there is 13 metres that averages 1.13% Li
2
O. The pegmatite is a
moderately-dipping dyke that trends for over 800 metres on surface with an average width of 25 metres.
The hole was drilled towards the south end of the dyke. A narrow, barren pegmatite dyke was also
intercepted from 99 metres to 108 metres. (Table 1; Figures 2 & 3). Drill hole YLP0046 did not intercept
pegmatite demonstrating the southern limit of the dyke. On the other hand, drill hole YLP0047 that was
collared near the north end of the dyke intercepted 16 metres of 0.94% Li
2
O from 64 metres, including
12 metres of 1.12% Li
2
O from 67 metres.
Drill hole YLP0040 was drilled in the mid-section of the Shorty dyke where it intercepted 8 metres of
1.26% Li
2
O from 157 metres (Table 1; Figures 4 & 5).
Drill hole YLP0043 was drilled in the southern section of the BIG-East dyke complex, intersecting three
pegmatite dykes. The hole collared in pegmatite at 1.33 metres intersecting 13.67 metres of 1.22%
Li
2
O, including 7 metres of 1.64% Li
2
O from 7 metres. Further down the hole 11 metres of 0.84% Li
2
O
was intercepted from 26 metres. The last dyke had an intercept of 14 metres of 1.24% Li2O from 42
metres (Table 1; Figures 6 & 7).
Spodumene is the primary lithium mineral constituent of the dykes and occurs with varying amounts of
quartz, feldspar, and muscovite.
Figure 1 - Location of LIFT's Yellowknife Lithium Project. Drilling is focused on the Road Access
Group of pegmatites which are located to the east of the city of Yellowknife along a government-
maintained paved highway, as well as the Echo target in the Further Afield Group.
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/8766/181905_804723c754b77840_001full.jpg
Table 1 - Assay highlights for drill holes reported in this press release.
Hole No.
From
(m)
To (m)
Interval
(m)
Li
2
O %
Dyke
YLP0037
55
88
33
0.71
Fi-SW
inc.
60
73
13
1.13
YLP0040
157
165
8
1.26
Shorty
YLP0043
1.33
15
13.67
1.22
BIG-E
Inc.
7
14
7
1.64
and
26
37
11
0.84
and
42
56
14
1.24
YLP0046
No pegmatite intercepted
Fi-SW
YLP0047
64
80
16
0.94
Fi-SW
inc.
67
79
12
1.15
Figure 2 - Plan view showing the surface expression of the Fi SW pegmatite with diamond drill hole
reported in this press release.
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/8766/181905_804723c754b77840_002full.jpg
Figure 3 - Cross-section of YLP0037 which intersected the Fi SW dyke with a 33 metre interval of
0.71% Li
2
O.
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/8766/181905_804723c754b77840_003full.jpg
Figure 4 - Plan view showing the surface expression of the Shorty pegmatite with diamond drill holes
reported in this press release.
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/8766/181905_804723c754b77840_004full.jpg
Figure 5 - Cross-section of YLP0040 which intersected 8 metres at 1.26% Li
2
O in the Shorty
pegmatite dyke.
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/8766/181905_804723c754b77840_005full.jpg
Figure 6 - Plan view showing the surface expression of the BIG East pegmatite with diamond drill
holes reported in this press release.
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/8766/181905_804723c754b77840_006full.jpg
Figure 7 - Cross-section of YLP0043 which intersected
16
metres at 0.94% Li
2
O including 12 m at
1.15% Li
2
O
.
To view an enhanced version of this graphic, please visit:
https://images.newsfilecorp.com/files/8766/181905_804723c754b77840_007full.jpg
Table 2 - Drill collars table of reported drill holes in this press release
Hole No.
Easting
1
Northing
1
Elevation
(m)
Length
(m)
Azimuth
Dip
Dyke
YLP0037
371,150
6,940,539
248.2
123.0
300
44
Fi-SW
YLP0040
372,773
6,938,141
248.5
201.0
126
58
Shorty
YLP0043
346,012
6,932,947
211.3
80.0
122
46
BIG East
YLP0046
371,103
6,940,275
250.9
245
303
50
Fi SW
YLP0047
371,442
6,940,989
249.0
102.0
297
44
Fi-SW
1
UTM NAD83 zone 12
QA/QC and Core Sampling Protocols
All drill core samples were collected under the supervision of LIFT employees and contractors. Drill core
was transported from the drill platform to the logging facility where it was logged, photographed, and split
by diamond saw prior to being sampled. Samples were then bagged, and blanks and certified reference
materials were inserted at regular intervals. Field duplicates consisting of quarter-cut core samples were
also included in the sample runs. Groups of samples were placed in large bags, sealed with numbered
tags in order to maintain a chain-of-custody, and transported from LIFT's core logging facility to ALS
Labs ("ALS") laboratory in Yellowknife, Northwest Territories.
Sample preparation and analytical work for this drill program were carried out by ALS. Samples were
prepared for analysis according to
ALS method CRU31: individual samples were crushed to 70%
passing through 2 mm (10 mesh) screen; a 1,000 gram sub-sample was riffle split (SPL-21) and then
pulverized (PUL-32) such that 85% passed through 75 micron (200 mesh) screen. A 0.2 gram sub-
sample of the pulverized material was then dissolved in a sodium peroxide solution and analysed for
lithium according to ALS method ME-ICP82b. Another 0.2 gram sub-sample of the pulverized material
was analysed for 53 elements according to ALS method ME-MS89L. All results passed the QA/QC
screening at the lab, all inserted standards and blanks returned results that were within acceptable limits.
Qualified Person
The disclosure in this news release of scientific and technical information regarding LIFT's mineral
properties has been reviewed and approved by Carl Verley, P.Geo., Vice-President, Exploration of Li-
FT Power and a Qualified Person as defined by National Instrument 43-101 Standards of Disclosure for
Mineral Projects (NI 43-101).
About LIFT
LIFT is a mineral exploration company engaged in the acquisition, exploration, and development of
lithium pegmatite projects located in Canada. The Company's flagship project is the Yellowknife Lithium
Project located in Northwest Territories, Canada. LIFT also holds three early-stage exploration
properties in Quebec, Canada with excellent potential for the discovery of buried lithium pegmatites, as
well as the Cali Project in Northwest Territories within the Little Nahanni Pegmatite Group.
For further information, please contact:
Francis MacDonald
Chief Executive Officer
Tel:
+ 1.604.609.6185
Email:
Website:
www.li-ft.com
Cautionary Statement Regarding Forward-Looking Information
Certain statements included in this press release constitute forward-looking information or statements
(collectively, "forward-looking statements"), including those identified by the expressions "anticipate",
"believe", "plan", "estimate", "expect", "intend", "may", "should" and similar expressions to the extent
they relate to the Company or its management. The forward-looking statements are not historical facts
but reflect current expectations regarding future results or events. This press release contains forward
looking statements. These forward-looking statements and information reflect management's current
beliefs and are based on assumptions made by and information currently available to the company
with respect to the matter described in this new release.
Forward-looking statements involve risks and uncertainties, which are based on current expectations
as of the date of this release and subject to known and unknown risks and uncertainties that could
cause actual results to differ materially from those expressed or implied by such statements.
Additional information about these assumptions and risks and uncertainties is contained under "Risk
Factors and Uncertainties" in the Company's latest annual information form filed on March 30, 2023,
which is available under the Company's SEDAR+ profile at
www.sedarplus.ca
, and in other filings that
the Company has made and may make with applicable securities authorities in the future. Forward-
looking statements contained herein are made only as to the date of this press release and we
undertake no obligation to update or revise any forward-looking statements whether as a result of new
information, future events or otherwise, except as required by law. We caution investors not to place
considerable reliance on the forward-looking statements contained in this press release.
Neither the Canadian Securities Exchange (the "CSE") nor its Regulation Services Provider (as that
term is defined in the policies of the CSE) accepts responsibility for the adequacy or accuracy of this
release.
To view the source version of this press release, please visit
https://www.newsfilecorp.com/release/181905