Galway Metals Intersects Wide, High-Grade, VMS Mineralization in Gap Area at its Estrades Project in Quebec
Galway Metals Intersects Wide, High-Grade, VMS Mineralization in Gap Area at its Estrades
Project in Quebec
TORONTO, ON / ACCESSWIRE / July 26, 2018 / Galway Metals Inc. (TSX-V: GWM, OTC PINK:
GAYMF) (the "Company" or "Galway") is pleased to report assay results from 10 additional drill holes
plus two extensions (7,224 metres) at its former producing, 100%-owned, 20,915 hectare, Estrades
polymetallic property located in the northern Abitibi of western Quebec, Canada. This brings Galway's
total drill results reported to date at Estrades to 20,707 metres in 34 holes (plus 3 stopped due to
deviation) plus three wedges (in addition to 501 m in one hole at Newiska; 2,191 m in five holes at
Newiska are pending); a total of approximately 200,000 metres have been drilled on Galway's Estrades
property since discovery in the 1970's. The drill program was designed to expand the existing resource on
the periphery of known zones at shallow depths, and to probe deeper holes close to potential high-grade
hydrothermal source vents.
"We are pleased that our drilling of the gap area immediately east of the cross fault and ramp continues
to yield strong gold, silver and zinc mineralization over wide widths. This drilling continues to confirm
expectations as indicated by the Titan geophysical anomaly in this area. We are looking forward to
incorporating these and other drill results in the pending Estrades resource update, which will be out in
the third quarter" cites Robert Hinchcliffe, President and CEO of Galway Metals.
Drilling Highlights
Located East of the Cross Fault and Ramp in a Gap Between the Main and Central Zones Outside the
Resource;
Remains Open Above and Below (Figure 1)
4.3 g/t Au, 115.2 g/t Ag, 11.0% Zn, 0.8% Cu and 0.9% Pb over 7.1 m (5.2 m true width (TW))
at a vertical depth of 288 m below surface, (including 6.0 g/t Au, 212.5 g/t Ag, 16.2% Zn, 0.6%
Cu and 1.8% Pb over 2.85 m), in GWM-18E-48.
3.0 g/t Au, 176.0 g/t Ag, 17.9% Zn, 0.3% Cu and 0.9% Pb over 5.4 m (3.4 mTW) at a vertical
depth of 456 m below surface, in GWM-18E-32.
Located in the Central Part of the Central Zone, Down Dip From and Outside the Existing Resource;
Remains Open Below
1.3 g/t Au, 88.1 g/t Ag, 6.5% Zn, 0.7% Cu and 0.3% Pb over 4.8 m (3.3 m TW) at a vertical
depth of 321 m below surface, (including 1.7 g/t Au, 95.0 g/t Ag, 14.5% Zn, 0.5% Cu and 0.8%
Pb over 2.0 m), plus 0.6 g/t Au, 74.5 g/t Ag, 3.0% Zn and 4.1% Cu over 1.0 m (0.7 m TW) in
GWM-18E-42.
1.5 g/t Au, 40.0 g/t Ag and 3.9% Zn over 6.8 m (5.1 m TW) at a vertical depth of 286 m below
surface, (including 1.8 g/t Au, 35.3 g/t Ag and 4.8% Zn over 4.7 m (3.5 m TW) in Hole GWM-
18E-43.
Extends Copper-Rich Shoots Along the Eastern Side of the Central Zone in Areas That Were Previously
Believed to be Waste and Therefore Outside the Existing Resource; Remains Open Below
15.7 g/t Ag and 2.2% Cu over 1.9 m (0.9m TW) at a vertical depth of 531 m below surface,
(including 4.4% Cu over 0.6 m (0.3m TW), plus 37.9 g/t Ag, 0.3% Zn and 2.9% Cu over 0.8 m
(0.4m TW), plus 22.3 g/t Ag and 1.9% Cu over 0.5 m (0.2m TW) in GWM-18E-46B.
1.0 g/t Au, 11.9 g/t Ag and 2.2% Cu over 1.8 m (0.9 m TW) at a vertical depth of 419 m below
surface, (including 2.2 g/t Au, 18.5 g/t Ag and 4.7% Cu over 0.6 m), plus 0.5 g/t Au, 64.8 g/t Ag
and 3.6% Cu over 0.8 m (0.4 m TW) in GWM-18E-18.
Notes: Holes were not drilled in sequential numerical order. Holes GWM-17E-20, 22, 33-40, and 44 were
not drilled; holes 23, 25 and 26 were stopped short of target. Initial attempts at drilling holes 21 and 46
equaled 792m, and were stopped due to excessive deviation.
The four Galway holes in the area just east of the cross fault and ramp are all high-grade and
represent what is likely to be a significant extension to the current resource, which will be updated
in coming weeks (see below). The TITAN geophysical survey undertaken by Quantec Geoscience for
Galway appears to indicate that this new zone is continuous to depths greater than 2,000 metres on three
lines covering 400 metres of strike length (Figure 2). These results are within the chargeability high and
resistivity low anomaly identified by the Titan survey. The MT-referenced IP chargeability models show
clear high responses to their maximum depths of 750 m, while the MT-referenced EM resistivity models
show clear low responses as continuous structures to depths greater than 2,000 m. As expected, the IP
high and EM low responses are spatially coincident with each other. Drilling has been stopped since the
end of April (end of the winter drilling season). Future plans are to drill the area above hole 48 this
coming winter.
"We believe the new area will make the economics of the deposit far more enticing because this large
area of wide, high grade mineralization would be the first zone encountered if development from the
existing ramp were to take place going east. A gravity survey to be completed in the next couple of months
should augment the TITAN survey which has identified numerous strong anomalies on the
property (Figure 3)," cites Mike Sutton, VP Exploration of Galway Metals.
Review of Drill Results:
Results from hole 48 of 7.1 metres grading 11.0% Zn, 4.3 g/t Au, 115.2 g/t Ag, extends toward surface
the previously intersected high-grade mineralization (holes 27 and 24) that exists immediately east of the
cross fault and ramp and remains open for 236 metres above (Figure 1). This drill hole extended
mineralization 45 m above, and 58 m east of hole 24, which returned 5.2 g/t Au, 198.7 g/t Ag and 15.7%
Zn over 1.5 m, and 158 m above hole 27, which returned 2.2 g/t Au, 181.0 g/t Ag and 28.5% Zn over
3.3 m, plus 190.7 g/t Ag and 18.6% Zn over 2.6 m at vertical depths of 435 metres and 453 metres,
respectively. None of these holes are in the current resource estimate and remain open above and below.
Results from the extension of hole 32, which returned 5.4 metres grading 17.9% Zn, 3.0 g/t Au and
176.0 g/t Ag, extends to the east and to depth previously intersected high-grade mineralization. The zone
remains open below this hole and the strong mineralization encountered in hole 27. This drill hole
extended hole 27 mineralization 49 m to the east (and 12m below), and is 111 m below hole 24, and 158
m below hole 48, Together, these drill results represent a strong vertical corridor of high-grade
mineralization that coincides with the Titan IP and EM anomaly that measures 400 metres along
strike and at least 2,000 metres deep. These drill intersects will, for the first time, be incorporated
in the pending resource update, and remains open to surface and to depth.
Holes 41, 42, 43 and 45 add mineralization to the central part of the Central Zone either in areas that were
previously believed to be waste or down dip from the existing resource, and they remain open below. The
intersections in hole 42 (1.3 g/t Au, 88.1 g/t Ag, 6.5% Zn, 0.7% Cu and 0.3% Pb over 4.8 m) exist in a
necked down narrow portion of the resource (it was drilled in an area that was previously thought to
contain below cutoff grade mineralization) and is located 50 m west of hole 43 (1.5 g/t Au, 40.0 g/t Ag
and 3.9% Zn over 6.8 m) and 188 m above hole 41 (1.9 g/t Au, 13.9 g/t Ag and 5.3% Zn over 0.7 m).
The intersection in hole 43 exists 35 m from the closest resource hole in this area and would extend the
resource into an area previously thought to be barren. None of these holes are in the current resource
estimate.
Holes 18, 29, 46B and 47 were drilled to extend high grade copper shoots on the eastern side of the
Central Zone that were in areas previously believed to be waste. Hole 46B (15.7 g/t Ag and 2.2% Cu
over 1.9 m) extends mineralization 35m from the mineralization encountered in hole 29 (37.3 g/t Ag and
1.3 Zn over 2.0 m) and 217 m below previously released hole 16 (22.4 g/t Au, 199.3 g/t Ag, 10.4%
Zn and 2.0% Pb over 1.6 m), and is also not in the resource. Hole 46B is 296 m vertically below the
closest resource hole in this area. Hole 18 (1.0 g/t Au, 11.9 g/t Ag and 2.2% Cu over 1.8 m) extends
mineralization 123 m below previously released hole 17 (0.2 g/t Au, 76.1 g/t Ag, 0.4% Zn and 3.7% Cu
over 1.6 m). Both of these holes, as well as holes 14, 16, 29, 46 and 47, were drilled in an area that
was previously believed to be waste. These drill intersections will be incorporated in the pending
resource update, and they remain open below.
Hole 21, and the extension of hole 28, did not reach their targets; further extensions or wedges will follow
after downhole geophysics is undertaken. Hole 21 did intersect extremely altered rhyolite with abundant
talc and with an assay of 1.0% Zn over 1.4 m (TW Unknown) at a vertical depth of 1,150 m below
surface at the end of the hole. The TITAN survey appears to indicate strongly anomalous geophysical
responses in the vicinity of this hole. This is the deepest hole drilled at Estrades. It targeted the down-
plunge extension of the Main Estrades deposit below the bottom of the current resource. Before extending
or wedging this hole, downhole geophysics will take place to see if the Main zone extension might be just
to the south. The entire 400-metre area of interest beneath the resource can be drilled by wedging off of
this hole.
Updated Resource Expected in Third Quarter
Galway drilled at Estrades in an effort to expand the existing resource, and has completed 34 holes (plus 3
stopped due to deviation), plus 3 wedges since the existing resource was announced, which coincided
with the project's acquisition in August 2016. The company has been successful, with drilling located
outbound from existing resources, at returning intersections such as:
72.5 g/t Au over 1.6 metres (1.0m TW) in Hole GWM-17E-01,
7.4% Cu over 1.9 m (1.2m TW) in Hole GWM-17E-05,
5.1% Cu and 62.0 g/t Ag over 1.65 m (1.2m TW), including 12.9% Cu and 159.0 g/t Ag over
0.55 m (0.4m TW), in hole GWM-17E-04, and
22.4 g/t Au, 199.3 g/t Ag, 10.4% Zn and 2.0% Pb over 1.6 m (0.8m TW), in Hole GWM-17E-
16.
The Company has also been successful at drilling newly identified zones, with intersections returned such
as:
2.2 g/t Au, 181.0 g/t Ag and 28.5% Zn over 3.3 m (2.1m TW), plus 190.7 g/t Ag and 18.6% Zn
over 2.6 m (1.7m TW), plus 5.7 g/t Au and 43.2 g/t Ag over 2.6 m (unknown TW), plus 4.7 g/t
Au, 67.5 g/t Ag, 4.9% Zn, 2.1% Cu and 1.0% Pb over 1.8m (1.1m TW) in GWM-17E-27,
5.2 g/t Au, 198.7 g/t Ag, 15.7% Zn and 1.3% Pb over 1.5 m (0.8 m TW), plus 2.3 g/t Au, 65.7
g/t Ag and 12.6% Zn over 2.1 m (1.2 m TW) in GWM-17E-24,
6.9 g/t Au, 78.5 g/t Ag and 1.7% Zn over 6.4 m (4.4m TW) in GWM-18E-31, and
1.1 g/t Au, 95.2 g/t Ag and 4.2% Zn over 17.7 m (including 1.7 g/t Au, 190.9 g/t Ag, 9.7% Zn
and 1.3% Cu over 4.5 m, and 1.0 g/t Au, 147.6 g/t Ag and 8.3% Zn over 2.0 m) (unknown TW)
in GWM-17E-08.
The priority was to drill off gaps in the 1.8 km long resource to create more resources along this sheet of
vertical mineralization.
On August 18, 2016, Galway published a NI 43-101 compliant Estrades resource estimate (Table 1),
which included Indicated Resources of 518,000 ounces at 12.4 g/t gold equivalent (or 652,000,000 lbs at
22.8% zinc equivalent), plus Inferred Resources of 290,000 ounces at 7.4 g/t gold equivalent (or
366,000,000 lbs at 13.6% zinc equivalent) (refer to Galway's website at www.galwaymetalsinc.com for
details on the Estrades resource estimate). The Estrades project was previously mined via a 200 metre
deep ramp, with production in 1990-91 totaling 174,946 tonnes grading 12.9% Zn, 6.4 g/t Au, 1.1% Cu
and 172.3 g/t Ag. Galway is planning to release an updated resource in the third quarter, taking into
account new drilling results received since the 2016 resource.
Table 2: Drill Result Highlights
Hole ID
From
(m)
To
(m)
Intercept
(m)
TW
(m)
Au Eq*
(g/t)
Zn Eq*
(%)
Au
(g/t)
Ag
(g/t)
Zn
(%)
Cu
(%)
Pb
(%)
Type**
GWM-18E-48 342.7 349.8 7.1 5.2 14.3 26.3 4.3 155.2 11.0 0.8 0.9 MSS
including 345.0 347.9 2.9 2.1 19.7 36.3 6.0 212.5 16.2 0.6 1.8 MSS
GWM-18E-45 503.8 506.0 2.2 1.5 2.8 5.1 1.3 20.6 2.2 MSS
GWM-18E-43 331.7 338.5 6.8 5.1 4.2 7.7 1.5 40.0 3.9 MSS
including 331.7 336.4 4.7 3.5 4.9 9.0 1.8 35.3 4.8 MSS
GWM-18E-42 361.8 366.6 4.8 3.3 14.8 1.3 88.1 6.5 0.7 0.3 MSS
including 361.8 363.8 2.0 1.4 23.7 1.7 95.0 14.5 0.5 0.8 MSS
and 352.9 354.0 1.1 0.8 2.6 1.3 33.9 1.1 0.4 MSS
and 359.2 359.7 0.5 0.3 36.4 1.3 SMS
and 371.4 372.4 1.0 0.7 0.6 74.5 3.0 4.1 SMS
GWM-18E-41 531.4 532.1 0.7 0.4 5.0 9.2 1.9 13.9 5.3 SMS
and 533.1 533.7 0.7 0.4 0.5 21.9 0.9 SMS
GWM-18E-32 490.3 495.7 5.4 3.4 29.8 3.0 176.0 17.9 0.3 0.9 MSS
GWM-18E-47 405.9 414.3 8.4 5.1 5.1 0.2 25.9 2.4 0.5 0.1 DSS
including 405.9 407.8 1.9 1.2 8.2 0.4 42.7 4.3 0.6 0.2 DSS
which includes 407.3 407.8 0.5 0.3 14.7 1.0 62.8 6.9 1.2 0.7 DSS
including 411.0 411.8 0.8 0.5 0.6 31.6 3.5 3.6 SMS
and 400.5 401.0 0.5 0.3 5.1 88.5 2.7 DSS
and 416.5 417.5 1.0 0.6 15.9 0.5 1.9 DSS
and 420.0 421.0 1.0 0.6 4.0 10.5 2.2 0.5 DSS
GWM-18E-46B 473.1 475.0 1.9 0.9 15.8 2.2 DSS
including 474.4 475.0 0.6 0.3 4.4 SMS
and 388.3 388.8 0.5 0.2 0.7 DSS
and 436.6 437.2 0.6 0.3 2.5 4.7 0.9 26.4 2.3 DSS
and 442.4 442.9 0.5 0.2 8.7 0.8 63.2 3.5 0.5 0.6 SMS
and 451.7 452.4 0.8 0.4 0.3 37.9 0.3 2.9 DSS
and 464.4 465.0 0.6 0.3 0.3 0.9 DSS
and 466.4 466.9 0.5 0.2 22.3 1.9 DSS
GWM-18E-29 391.0 393.0 2.0 1.0 0.6 37.3 1.3 0.4 SMS
including 391.0 392.0 1.0 0.5 1.2 58.5 1.4 0.7 SMS
and 404.0 404.5 0.5 0.2 0.4 23.6 1.6 SMS
and 440.4 441.2 0.8 0.4 7.7 2.3 SMS
and 445.7 446.3 0.6 0.3 1.3 SMS
and 447.3 448.1 0.9 0.4 1.2 SMS
and 459.0 460.0 1.0 0.5 5.5 10.2 3.4 0.6 SMS
and 475.0 478.0 3.0 1.5 4.9 0.1 0.5 SMS
including 475.0 475.8 0.8 0.4 19.6 1.1 SMS
including 477.5 478.0 0.5 0.2 0.7 0.6 SMS
GWM-18E-18 424.5 426.3 1.8 0.9 1.0 11.9 2.2 DSS
including 425.7 426.3 0.6 0.3 2.2 18.5 4.7 DSS
and 381.8 382.5 0.6 0.3 4.1 0.3 27.5 1.9 0.2 DSS
and 388.9 390.4 1.5 0.7 0.4 25.5 1.0 SMS
and 420.4 421.2 0.8 0.4 0.5 64.8 3.6 DSS
Notes:
*Au (Eq g/t) and Zn (Eq %) represent the in-situ metal content expressed as Au and Zn equivalents.
Equivalents are not provided when the underlying Au and/or Zn metal content is below 25% of the
intersect value.
Preliminary analysis indicates that no metal is dominant; however, Au and Zn are the largest contributors
to the Estrades resource.
Equivalencies are calculated using the following metal prices (US$) and exchange rate (US$/C$)
provided by RPA:
Au $1,450/oz, Ag $21.00/oz, Zn $1.15/lb, Cu $3.50/lb, Pb $1.00/lb, US$0.80/C$1.00.
** MSS = massive sulphide, SMS = semi-massive sulphide DSS = disseminated and stringer sulphides.
Holes were not drilled in sequential numerical order; holes GWM-17E-20, 22, 33-40, and 44 were not
drilled.
If true width (TW) is not specified, the orientation of the zone is unknown at this time.
Estrades, Newiska, and Casa Berardi Geology and Mineralization
Information on Geology and Mineralization can be found on the Estrades project page of our website
at www.galwaymetalsinc.com along with a complete Table of Drill Results released to date.
Review by Qualified Person, Quality Control and Reports
In compliance with National Instrument 43-101, Mr. Mike Sutton, P.Geo., is the Qualified Person
responsible for the accuracy of this news release. Mr Reno Pressacco, P. Geo., is the Qualified Person
responsible for preparation and disclosure of the Estrades Mineral Resource estimate, and is independent
of Galway. The drill core is sawn in half with one half of the core sample shipped to Swastika
Laboratories situated in Swastika, ON, which has accreditation of ISO/IEC 17025. The other half of the
core is retained for future assay verification. Other QA/QC measures includes the insertion of certified
reference standards (gold and polymetallics) and blanks into the sample stream, and the regular re-
assaying of pulps and rejects at alternate certified labs. Gold analysis is conducted by fire assay using
atomic absorption or gravimetric finish for samples greater than 10 g/Mt gold. Other Metals (Ag, Cu, Pb,
Zn, Co, As) have full acid digestion and analyzed by AAS; with over limits (5000 PPM) analyzed by
AAS using method dilutions, and the Silver (Ag) over limits (> 200 ppm) analyzed by fire assay (FA) &
gravimetric finish. The laboratory re-assays at least 10% of all samples and additional checks may be run
on anomalous values.
Table 3: Drill Hole Coordinates
Hole ID Azimuth Dip Northing Easting Hole Length (m)
GWM-18E-48 176.0 -59.0 5494933 654553 369
GWM-18E-45 327.0 -70.0 5494583 654821 522
GWM-18E-43 359.0 -66.0 5494618 654950 444
GWM-18E-42 334.0 -67.0 5494618 654950 450
GWM-18E-41 326.0 -77.0 5494618 654950 552
GWM-18E-32 175.0 -66.0 5494933 654553 150
GWM-18E-47 15.0 -70.0 5494618 654950 501
GWM-18E-46B 22.9 -80.2 5494732 655146 522
GWM-18E-29 1.0 -79.0 5494732 655146 486
GWM-18E-21EW3 (+wedges+21) 220.7 -81.0 5495152 654315 1,901
GWM-18E-18 316.0 -78.0 5494732 655146 453
GWM-18E-28C 135.6 -69.5 5494951 654406.2 823
About the Company
Galway Metals is well capitalized with two projects in Canada: Clarence Stream, an emerging gold
district in New Brunswick, and Estrades, the former producing, high-grade VMS mine in Quebec. The
Company began trading on January 4, 2013, after its successful spinout to existing shareholders from
Galway Resources following the completion of the US$340 million sale of that company. With
substantially the same management team and Board of Directors, Galway Metals is keenly intent on
creating similar value as it had with Galway Resources.
Should you have any questions and for further information, please contact (toll free):
Galway Metals Inc.
Robert Hinchcliffe
President & Chief Executive Officer
1-800-771-0680
www.galwaymetalsinc.com
CAUTIONARY STATEMENT: Neither the TSX Venture Exchange nor its Regulation Services Provider
(as that term is defined in the policies of the TSX Venture Exchange) accepts responsibility for the
adequacy of this news release. No stock exchange, securities commission or other regulatory authority has
approved or disapproved the information contained herein.
This news release contains forward-looking information, which is not comprised of historical facts.
Forward-looking information involves risks, uncertainties and other factors that could cause actual events,
results, performance, prospects and opportunities to differ materially from those expressed or implied by