Gensource Announces 2019 Drilling Results
Gensource Announces 2019 Drilling Results
SASKATOON, Saskatchewan--(BUSINESS WIRE)--February 27, 2020--Gensource Potash
Corporation (“Gensource” or the “Company”) (TSX-V: GSP), a near-term potash producer
focused on sustainable production, is pleased to provide a summary of the results obtained from
its 100% owned Vanguard Area in south-central Saskatchewan completed in December 2019.
The drilling, coring, and assay work has resulted in an overall increase in the Measured and
Indicated Resource in the Vanguard Area.
From a news release dated January 30, 2020 (see http://gensourcepotash.ca/company-news/),
readers understand Gensource is in the latter stages of project finance for its Tugaske Project.
Tugaske is designed to be a small-scale, environmentally sustainable potash production facility
and has attracted significant attention from strong industry players. Helm AG of Germany and its
US subsidiary, Helm Fertilizers, the project’s off-taker, is committing to purchase 100% of the
production for an initial period of 10 years, renewable thereafter. The Tugaske Project employs
innovative selective extraction techniques that produce no tailings and requires no brine ponds,
eliminating two of the most negative environmental impacts on the land. This method also
consumes significantly less fresh water compared to existing legacy mining techniques.
Gensource contracted CWC Ironhand Drilling (“CWC”) to complete the well. CWC is an
industry-leading drilling contractor operating in western Canada. CWC was supported by many
service providers at the site, including Artisan Consulting Services Ltd. (“Artisan”) who
provided drill site supervision and coordination for this well on behalf of Gensource. Artisan is a
privately owned and operated consulting company located in Carlyle, Saskatchewan, specializing
in supplying supervision services for the drilling of vertical, directional and horizontal wells
within western Canada for the past 30+ years. Artisan has overseen all wells drilled by
Gensource in the Vanguard Area. Figure 1 shows CWC Rig #2 at the drill site.
The outcome of this work provides further evidence that the Vanguard Area overlies a rich and
thick potash resource. This Resource information provides a clear view to the Area’s capability
to accommodate multiple small-scale Gensource potash facilities, each being an independent
economic entity on its own, referred to as a module. Detailed results from the drilling program
are disclosed below.
The current NI 43-101 Technical Report (“Technical Report”) for the Vanguard Area (dated
February 23, 2018 and available on SEDAR or the Company’s website) summarizes the
Feasibility Study and defines the Resource and Reserve for one of Gensource’s small-scale,
environmentally friendly potash production modules. By definition, a Feasibility Study relies, for
all project economic and life-of-mine information, entirely on the defined Reserve in the
Vanguard Area. Therefore, the definition of adjusted Resources in the Vanguard Area with no
change to the Reserves, has no material impact on the current Technical Report. On that basis,
the referenced Technical Report, dated February 23, 2018, remains the most current reference for
the Vanguard Area.
“As we fully expected, this drilling initiative continued to demonstrate an excellent resource in
our Vanguard Area, said Mike Ferguson, President & CEO of Gensource. “Saskatchewan is
fortunate to have a potash resource that is well-defined, high-grade and consistent over large
areas - all of these attributes are especially supportive of our planned selective solution extraction
method. The results of this drilling further confirm the quality and abundance of the potash
resource in the Vanguard Area, and further affirm the Vanguard Area is capable of supporting
several potash modules, consistent with the Company’s business plan.”
Summary of Results:
Drilling of a single exploration well commenced in November 2019. The work was completed in
just under 4 weeks and over 5000 hours on-site. There were zero injuries, zero reportable
incidents, and no environmental issues associated with this drilling work. This is the fourth
exploration well completed on the Vanguard area since 2016. These wells, combined with the
data from two pre-existing wells drilled in 2012 that were acquired with the property, accounts
for the total of 6 wells completed in the Vanguard Area (all on Lease KL245). Figure 2 shows
the 6 drilling locations across the Vanguard Area, including the location of the new well drilled
(“8-4”).
The well was drilled into the Precambrian Basement to a total depth of approximately 2200 m,
with the lower 30 m of the Deadwood Formation bearing a basal sandstone that offers a good
target for the potential use as a disposal well. Approximately 54 m of core was recovered from
the Prairie Evaporite Formation (Saskatchewan’s potash bearing formation). The coring strategy
for this well was to focus core recovery on the Patience Lake and Belle Plaine members of the
Prairie Evaporite, and exclude the Esterhazy member, because of the priority and likelihood of
the Patience Lake and Belle Plaine being targeted mining zones; since the Esterhazy member
often contains higher values of carnallite, it is often excluded from mining considerations – this
was the case for the quantification of the Resource and Reserve in Gensource’s Feasibility Study.
This strategy helped improve the cost and schedule of the drilling program. It should be noted,
however, that the presence of all 3 potash members has been confirmed by the geophysical logs
completed in the well.
From the drilling location, the core was transported to SRC Laboratories in Saskatoon, where it
was then logged by independent geologists from Terra Modelling Services Inc. Figure 3 shows
core being logged in the lab.
Over 150 samples were selected from sylvinite-bearing core for assaying. The resulting assay
data has been analyzed. Gensource’s initial mining target, as defined in the Feasibility Study
Technical Report, is the uppermost potash member of the Prairie Evaporite formation, the
Patience Lake Member. The assay results from the 8-4 well indicate the following information
for the Patience Lake Member:
Average grade of approximately 34.4% KCl
Average total thickness of approximately 13.9 m
Of particular note are high-grade intersections of 56% KCl over 0.4m and with some
individual samples measuring as high as 67% KCl
Table 1 demonstrates the general consistency in the recent drilling results (8-4, outlined in red)
with the nearby wells previously drilled by Gensource in the Vanguard Area; focused on the
Patience Lake Member.
In accordance with the CIM Definition Standards (2014), and using the assumed baseline
recovery of 40% (discussed in more detail in the Feasibility Study Technical Report), the
resource in the Vanguard Area has been updated to 209 million tonnes of final, salable potash
product in the Measured category, and 75 million tonnes in the Indicated category, for a
combined 286 million tonnes. This represents approximately a 10% increase in the Measured and
Indicated Resource numbers for the Vanguard Area compared to those previously published. Of
particular note is an increase of approximately 25% in the combined Measured and Indicated
Resource of the Patience Lake Member. The CIM Definition Standards (2014) provide for a
direct relationship between Indicated Mineral Resources and Probable Mineral Reserves, and
between Measured Mineral Resources and Proven Mineral Reserves. Therefore, with further
engineering definition (specifically, further detailed wellfield planning) and incorporation of the
applicable modifying factors, additional mineral Reserves can be identified from these Indicated
and Measured Resource categories. Table 2 shows a sensitivity analysis regarding the summary
of the updated Resource numbers based on incorporating the data from the 8-4 well with the data
from the previous wells drilled.
The resource model was constructed as a 3D integrated stratigraphic grid model, using all
available drilling information. The basic assumptions for the resource model and subsequent
calculations are as follows:
K2O cut-off grade of 15% (equating to 24.6% KCl).
Maximum carnallite cut-off of 6%.
No insoluble cut-off.
No thickness cut-off, due to the mining methodology (i.e., selective solution mining).
For the different Radius-of-Influence (ROI), the previous seismic surveys (2D and 3D)
indicate a relatively stable Prairie Evaporite Formation, with the notable exception of the
dissolution edge in the south, and the thinning in the northwest, well outside the 6000 m
Inferred interpolation range. The former was clipped out of the model altogether.
As such, the following ROI’s were used, which are the same as those used in the current
Feasibility Study Technical Report:
o An Inferred Radius-of-Influence of 6000 m was used
o An Indicated Radius-of-Influence of 2250 m was used
o A Measured Radius-of-Influence of 1500 m was used
All other anomalies were also clipped out of the model, except for Winnipegosis Mounds
where these did not necessarily indicate anomalous salt.
Further deductions for unseen / unknown anomalies included:
o 25% in the Inferred category
o 15% in the Indicated category (lowered to 10% within the extents of the 3D
seismic survey)
o 10% in the Measured category (lowered to 5% within the extents of the 3D
seismic survey)
Recovery rates: Based on the preliminary horizontal cavern selective solution mining
design assumptions, it is estimated that the overall percentage recovery of the targeted
horizontal cavern potash zone will range between 30% to 50%. As such, Gensource
proceeded with a “base case” of a 40%, with 30% and 50% shown as sensitivity analyses.
As part of this well, a drill stem test for formation water was conducted from the Mannville
Formation top through to the bottom of the Gravelbourg Formation. A single packer was set
above the top of the Mannville Formation. The test result was positive for groundwater.
Gensource will continue to assess all data gathered from the area, to determine if a suitable
brackish groundwater source exists to supplement the solution mining water demand.
Mike Ferguson further commented: “The completion of this work further supports Gensource’s
business approach to offer direct access to the resource and an opportunity for an off-taker to be
an owner of potash production for themselves. We want to thank Artisan, CWC, and all the
excellent service providers who contributed to the safe and successful completion of this well.
Their rigorous approach to safety, high-performance standards, and overall professionalism and
work ethic are a testament to the quality and competency of the drilling industry in Western
Canada, and in particular, Saskatchewan. We are also extremely pleased to have participation in
this well from several local-area service providers, readily showing that the local community can
provide top-notch services in the immediate vicinity of our site. With respect to Gensource’s
efforts advancing their first module in the Vanguard Area, the Tugaske Project is now in the
project financing stage, with detailed due diligence on-going. We continue to make excellent
progress on our Tugaske Project, and the efforts from this well support its advancement.
Together with our partners, we are excited with the Tugaske Project’s progress towards
implementation, aiming to initiate field work activities later this year.”
The technical information presented in this news release has been reviewed and approved by Mr.
Louis Fourie, P.Geo., from Terra Modelling Services Inc., who is a Qualified Person according
to NI 43-101 requirements, and an independent consultant to the Company.
About Terra Modelling Services
Terra Modelling Services Inc. is a geological consulting company based in Saskatoon,
Saskatchewan, offering exploration, economic assessment, reporting and due diligence, as well
as commodity price forecasting. A wide range of commodities, including potash, phosphate,
lithium, diamonds as well as base- and precious metals are covered. For further information
about Terra Modelling Services, visit: www.terramodellingservices.ca
About Gensource
Gensource is based in Saskatoon, Saskatchewan and is focused on developing the next potash
production facility in that province – but with a radically and fundamentally different approach
that takes ESG factors into consideration. Gensource’s President & CEO, Mike Ferguson,
P.Eng., has assembled a management and technical team with direct and specific expertise and
experience in potash development in Saskatchewan.
Gensource operates under a business plan that has two key components: (1) vertical integration
with the market to ensure that all production capacity built is directed, and pre-sold, to a specific
market, eliminating market-side risk; and (2) technical innovation which will allow for a small
and economic potash production facility, which is much friendlier to the environment to
construct and operate - the output of which can then be directed to a single, specific market.
Neither TSX Venture Exchange nor its Regulation Services Provider (as that term is defined
in the policies of the TSX Venture Exchange) accepts responsibility for the adequacy or
accuracy of this release.
Caution Regarding Forward-Looking Statements
This news release may contain forward looking information and Gensource cautions readers
that forward- looking information is based on certain assumptions and risk factors that could
cause actual results to differ materially from the expectations of Gensource included in this news
release. This news release includes certain "forward-looking statements”, which often, but not
always, can be identified by the use of words such as "believes", "anticipates", "expects",
"estimates", "may", "could", "would", "will", or "plan". These statements are based on
information currently available to Gensource and Gensource provides no assurance that actual
results will meet management's expectations. Forward-looking statements include estimates and
statements with respect to Gensource’ future plans, objectives or goals, to the effect that
Gensource or management expects a stated condition or result to occur, including the ability to
finance the Tugaske or the Project or other projects on terms which are economic or at all, the
establishment of vertical integration partnerships and the sourcing of end use potash purchasers.
Since forward-looking statements are based on assumptions and address future events and
conditions, by their very nature they involve inherent risks and uncertainties. Actual results
relating to Gensource’ financial condition and prospects, the ability to finance the Tugaske or
the Project or other projects on terms which are economic or at all, the ability to establish viable
vertical integration partnerships and the sourcing of end use potash purchasers could differ
materially from those currently anticipated in such statements for many reasons such as: failure
to finance Tugaske or the Project or other projects on terms which are economic or at all;
failure to settle a definitive joint venture agreement with a party and advance and finance the
project; changes in general economic conditions and conditions in the financial markets; the
ability to find and source off-take agreements; changes in demand and prices for potash;
litigation, legislative, environmental and other judicial, regulatory, political and competitive
developments; technological and operational difficulties encountered in connection with
Gensource’ activities; and other matters discussed in this news release and in filings made with
securities regulators. This list is not exhaustive of the factors that may affect any of Gensource’
forward-looking statements. These and other factors should be considered carefully, and readers
should not place undue reliance on Gensource’ forward-looking statements. Gensource does not
undertake to update any forward-looking statement that may be made from time to time by
Gensource or on its behalf, except in accordance with applicable securities laws.
Contacts
Gensource Potash Corporation:
Mike Ferguson, President and CEO
Telephone: (306) 974-6414
Email:[email protected]