GRG.V · 2025-01-29 12:00:00

Golden Arrow Reports a Strong Finish to Phase 2 Drilling, Including 224m

Exploration Programs

@ 0.2% Copper, at San Pietro Project, Chile

TSX Venture Exchange (TSX-V):

GRG

Frankfurt Stock Exchange (FSE):

G6A

OTCQB Venture Market (OTCQB):

GARWF

VANCOUVER, BC

Jan. 29, 2025

/CNW/ -

Golden Arrow Resources Corporation

(TSXV: GRG) (FSE: G6A) (OTCQB: GARWF)

Golden Arrow

" or the

Company

") is pleased to report results from the final two holes of the Phase 2 drill program at the San Pietro Copper-Gold-Iron-Cobalt Project in

Chile

San

Pietro

" or the "

Project

"). These two holes (SP-DDH-39 and SP-DDH-40) together with two of the previously reported holes from the program (SP-DDH-29 and

SP-DDH-38) confirm a broad extension of the Rincones target up to 400 metres to the south (see

Figure 1

). Each of the four holes has now reported intervals of

between 180 and 310 metres that average over 0.2% Cu and 0.03 g/t Au as well as significant cobalt and iron. This southern Rincones area is expected to have

significant positive impact on the Mineral Resource Estimate ("

MRE

") that is currently underway. Furthermore, the area remains sparsely drilled and open for

expansion, particularly towards the Colla target located approximately 600 metres further to the south-southeast.

Results of the final two holes are highlighted by:

180m

averaging 0.21% Cu, 0.07 g/t Au, 95 g/t Co and 12.9% Fe

starting at

276.73m

depth in hole SP-DDH-39, in an undrilled area

280m

south of SP-

DDH-38 and

220m

along trend from SP-DDH-29

Pervasive mineralization from

75 m

depth to nearly the end of the hole at 541 metres in SP-DDH-40, including

224 m

averaging 0.20% Cu, 0.03 g/t Au, 63

g/t Co and 11.6% Fe starting at 317.05 metres

Geologic modelling indicates continuity of mineralization of this hole with SP-DDH-38 and earlier holes along section (see

Figure 2

Brian McEwen

, VP Exploration and Development for Golden Arrow, commented,

"Phase 2 drilling has definitely finished on a high note. We are going into our

first resource estimate knowing that the infill program we designed has successfully confirmed what we had expected after our preliminary work: stronger

mineralization and better continuity than many previous interpretations. We believe this will translate into an MRE that shows our investors and stakeholders

that we have again discovered a substantial deposit with strong upside and value-creation potential. Phase 2 might be done but we can't wait to get back out

into the field to keep drilling and building Rincones, potentially all the way to Colla, as well as continuing to make new discoveries at our many targets

throughout the massive project area, including some exciting prospects that were newly identified in 2024."

The Phase 2 drill program was executed in 2024, including an additional 24 holes, or 8292 metres of drilling on the Rincones advanced exploration target and 2

holes with a total of 607 metres drilled at the early-stage Colla target. Mineralization at the project is hosted in magnetite-rich mantos that are highly magnetic, as

well as structurally-related specularite breccias and veins. In late 2024 the Company completed a new detailed ground magnetic survey over the Rincones and

Colla targets to further delineate the targets and prioritize areas for the next phase of drill testing. In addition, since 2023 company geologists have been engaged

in detailed geologic mapping throughout the nearly 20,000 hectares of concessions, work which had not been undertaken by previous operators. The 2024

mapping and surface sampling program in the southern project area identified new prospective targets, including Noemi and Lolita N (

Figure 1

), and a ground

magnetics survey covering 1500 hectares was completed late in the year. Data from the surveys is still being processed.

Table 1. Summary of New Intervals, Phase 2 Drilling

[Cu Grade >0.20% or Co Grade >200 g/t or Au Grade >0.2 g/t or

Fe Grade

>30%]

Hole

From

(m)

Interval (m)

(%)

(g/t)

(%)

Rincones Target

SP-DDH-39

200.00

202.30

2.30

0.35

0.05

10.9

231.00

236.00

5.00

0.14

0.13

335

4.0

276.73

456.85

180.12

0.21

0.07

12.9

includes

323.70

337.55

13.85

0.31

0.04

17.5

371.00

456.85

85.85

0.28

0.11

106

13.8

includes

451.72

456.85

5.13

0.90

0.52

431

15.2

SP-DDH-40

49.00

53.32

4.32

0.02

0.04

294

15.7

75.00

149.03

74.03

0.20

0.04

119

14.7

279.00

283.54

4.54

0.30

0.03

156

28.1

317.05

541.22

224.17

0.20

0.03

11.6

includes

329.00

341.00

12.00

0.49

0.05

106

14.3

381.87

386.67

4.80

2.15

0.30

167

33.8

473.00

477.10

4.10

1.13

0.06

128

21.1

Note: Intervals are downhole length. See hole descriptions in text for additional details.

Drill Hole Details

The San Pietro Project hosts multiple targets with strong Iron oxide-Copper-Gold and Cobalt mineralization (see

Figure 1

). This mineralization is typically found

within a pile of fine to porphyritic andesites that exhibit widespread potassic feldspar alteration. The mineralization is often associated with areas where a

superimposed quartz-scapolite alteration is more intense and there is a development of brecciation with specularite and massive replacement of magnetite.

SP-DDH-39

was collared 220 metres to the northwest of, and drilled parallel to, SP-DDH-29 which intersected

310.85m

averaging 0.19% Cu, 0.06 g/t Au, 127 g/t

Co and 12.2% Fe starting at

186.4m

depth, as reported on

October 31, 2024

. The new hole tested for mineralization along the general northwest structural trend

from SP-DDH-29 corresponding to a set of subparallel specularite breccias trending from east-west to northwest. The first 322 metres of the hole were

dominated by a porphyritic andesite, which is less permeable to the development of fracturing and the entry of mineralized solutions. From 322 metres to the end

of hole at 509 metres, the SP-DDH-39 shows a package of fine porphyritic andesites. These host a series of veinlets and crackle breccias with chalcopyrite-pyrite

and specularite including a higher-grade structure at 452 metres with a halo of disseminated magnetite. In addition, near the contact between the porphyritic and

fine andesites at 276 to 322 metres depth several mineralized structures were developed.

SP-DDH-40

filled in the area between the main Rincones target area and the step-out hole SP-DDH-38 (155 metres southwest) which recently reported 283

metres averaging 0.23% Cu, 0.04 g/t Au, 101 g/t Co and 15.5% Fe from 83 metres depth (see

January 21, 2025

news release). From 130 metres to the end of

the hole at 548 metres, the fine porphyritic andesite hosts a series of zones with veinlets and crackle breccias filled with chalcopyrite-pyrite. Additionally in this

hole there are a series of sub horizontal magnetite replacement mantos of 5 to 8 metres wide with >30% of total iron, and in some cases with high Cu-Au

mineralization, as demonstrated in the 4.80 metres interval with 2.15% Cu, 0.3 g/t Au and 33.8% Fe starting at 381.87 metres deep. The cross-section in Figure 2

demonstrates the modeled units and continuity with SP-DDH-38, as well as neighbouring holes SP-DDH-11 and SP-DDH-05 (reported on

July 12, 2023

Table 2. Drill Hole Collar Information

[PSAD 56 / UTM Zone 19 S]

Hole

Easting

Northing

Elevation (m)

Azimuth

(˚)

Final Depth (m)

SP-DDH-39

390572

7071002

1003

-60

509

SP-DDH-40

390653

7071424

997

-60

548

Methodology & QA/QC

This drilling campaign was completed by Sociedad de Servicios Andinos SpA of Copiapó,

Chile

, using diamond drill producing HQ-sized core. The Golden Arrow

field team, supervised by senior geologists, photographed and logged the entire length of core for each drillhole, as well as measured it for recovery and marked

it for sampling. Pieces of whole core approximately 10 to 15 cm long were selected and measured for specific gravity on average every 20 metres and targeting

all different lithologies. Subsequently, the core was cut in half with an electric saw. One half was labelled, bagged and sent for analysis and the other half retained

onsite. After completing the sampling of each hole, the samples were shipped to ALS Laboratory in Copiapo,

Chile

by a contract truck service. Sample

preparation and gold analysis by Fire Assay and reading by atomic absorption on 30 gm sample by method Au-AA23 was completed at the ALS facility in

Santiago

Chile

. Multi-element package by ICP-OES reading following a four-acid digestion by method ME-ICP61 was performed at ALS facilities in

Lima,

Peru

. Samples with over limits in copper (+ 10,000 ppm) were re-assayed by ore grade method Cu-OG62 that includes four acid digestion and ICP-OES reading.

The Company follows industry standard procedures for the work carried out on the San Pietro Project, with a quality assurance/quality control ("

QA/QC

program. Blank and standard samples were inserted in each batch of samples sent to the laboratory for analysis. Golden Arrow detected no significant QA/QC

issues with material effect on the data. The trajectory of all the holes drilled at San Pietro during this Phase 2 were measured using the gyroscope equipment

"Champ Navigator" that assures no interference from the magnetite in the ground. Additionally, all the core was orientated using the "Champ Ori" core orientator

to measure the azimuth and dip of structures.

About the San Pietro IOCG Project

The San Pietro Project covers approximately 20,000 hectares, 100 kilometres north of Copiapo. Situated between and adjacent to Capstone Copper's Manto

Verde Mine property and Santo Domingo Project, San Pietro is in the centre of a potential new copper-iron-cobalt district within an active, well-developed mining

region that is home to all the major iron oxide-copper-gold ("

IOCG

") deposits in

Chile

The Project is hosted by andesite units in a Cretaceous-aged volcano-sedimentary sequence associated with intrusive rocks including granodiorites and diorites of

similar age. The Project is located east of the Atacama Fault system, a major north-south regional structure, which was instrumental in controlling the

emplacement of the ore deposits in the area.

Mineralization at San Pietro is typical of an IOCG system, with the addition of cobalt, and occurs in mantos, breccias and veins within a zone of alteration

characterized by an association of actinolite, epidote, chlorite and scapolite. The mantos are replacement of andesite by magnetite and sulphides, with a roughly

southeast strike and a gentle dip to the SW. Breccias and veins crosscut the mantos, are often subvertical, and filled with specularite and sulphides.

Qualified Persons

The exploration programs are designed by the Company's geological staff and results are reviewed, verified (including sampling, analytical and test data) and

compiled under the supervision of

Brian McEwen

, P.Geol., VP Exploration and Development to the Company. Mr. McEwen is a Qualified Person as defined in

National Instrument 43-101 and has reviewed and approved the contents of the news release.

About Golden Arrow:

Golden Arrow Resources Corporation is a mining exploration company with a successful track record of creating value by making precious and base metal

discoveries and advancing them into exceptional deposits.

Golden Arrow is actively exploring its flagship property, the advanced San Pietro iron oxide-copper-gold-cobalt project in

Chile

, and a portfolio that includes nearly

125,000 hectares of prospective properties in

Argentina

The Company is a member of the Grosso Group, a resource management group that has pioneered exploration in

Argentina

since 1993.

ON BEHALF OF THE BOARD

"Joseph Grosso"

_______________________________

Mr.

Joseph Grosso

Executive Chairman, President and CEO

Neither the TSXV nor its Regulation Services Provider (as that term is defined in policies of the TSXV) accepts responsibility for the adequacy or accuracy of

this release.

This news release contains forward-looking statements. Generally, forward-looking statements can be identified by the use of terminology such as "anticipate",

"will", "expect", "may", "continue", "could", "estimate", "forecast", "plan", "potential" and similar expressions. Forward-looking statements address future events

and conditions and therefore involve inherent risks and uncertainties. All statements, other than statements of historical fact, that address activities, events or

developments management of the Company believes, expects or anticipates will or may occur in the future, including, without limitation, statements about the

Company's plans for its mineral properties; the Company's business strategy, plans and outlooks; the future financial or operating performance of the

Company; and future exploration and operating plans are forward-looking statements.

Forward-looking statements are subject to a number of risks and uncertainties that may cause the actual results of the Company to differ materially from those

discussed in the forward-looking statements and, even if such actual results are realized or substantially realized, there can be no assurance that they will have

the expected consequences to, or effects on, the Company. Accordingly, readers should not place undue reliance on the forward-looking statements. Factors

that could cause actual results or events to differ materially from current expectations include, among other things: risks and uncertainties related to the ability

to obtain, amend, or maintain licenses, permits, or surface rights; risks associated with technical difficulties in connection with exploration activities; the

possibility that future exploration. There may be other factors that cause results or events to not be as anticipated. Actual results may differ materially from

those currently anticipated in such statements. Readers are encouraged to refer to the Company's Management's Discussion and Analysis for a more detailed

discussion of factors that may impact expected future results. The forward-looking statements contained in this press release are made as of the date hereof or

the dates specifically referenced in this press release, where applicable. The Company undertakes no obligation to publicly update or revise any forward-

looking statements, unless required pursuant to applicable laws. All forward-looking statements contained in this press release are expressly qualified by this

cautionary statement.

We advise U.S. investors that the SEC's mining guidelines strictly prohibit information of this type in documents filed with the SEC. U.S. investors are cautioned

that mineral deposits on adjacent properties are not indicative of mineral deposits on our properties.

View original content to download multimedia:

https://www.prnewswire.com/news-releases/golden-arrow-reports-a-strong-finish-to-phase-2-drilling-including-224m--0-2-copper-at-san-pietro-project-chile-302362816.html

SOURCE

Golden Arrow Resources Corporation

View original content to download multimedia:

http://www.newswire.ca/en/releases/archive/January2025/29/c8188.html

%SEDAR: 00042897E

For further information:

For further information, please contact: Corporate Communications, Tel: 1-604-687-1828, Toll-Free: 1-800-901-0058, Email:

[email protected]

CO: Golden Arrow Resources Corporation

CNW 07:00e 29-JAN-25

← Back to feed