Golden Arrow Continues to Intersect Thick Zones of Copper and of Cobalt Mineralization at the San Pietro Iron-Copper-Gold-Cobalt Project, Chile
Golden Arrow Continues to Intersect Thick Zones of Copper and of Cobalt
Mineralization at the San Pietro Iron-Copper-Gold-Cobalt Project, Chile
TSX Venture Exchange (TSX-V):
GRG
Frankfurt Stock Exchange (FSE):
G6A
OTCQB Venture Market (OTCQB):
GARWF
VANCOUVER, BC
,
Sept. 10, 2024
/CNW/ -
Golden Arrow Resources Corporation
(TSXV: GRG) (FSE: G6A) (OTCQB: GARWF), ("
Golden Arrow
" or
the "
Company
") is pleased to report additional long intervals of copper mineralization, highlighted by the results from diamond drill hole SP-DDH-22 in the
Rincones target (see
Figure 1
):
110m
at 0.40% Cu, 0.08 g/t Au, 85 g/t Co and 18.0% Fe starting at
158 m
depth.
Includes
1.12m
at 10.35% Cu, 2.44 g/t Au, 470 g/t Co and 23.1% Fe
Figure 2
shows the projection of this thick mineralized interval to the surface and demonstrates the correlation and continuity with intervals in two parallel holes
across a distance of more than 290 metres through the central Rincones target area. Of note is the high-grade copper and gold intercept, reported above, that
occurs within the longer-mineralized interval. Intervals of higher grade were also noted within one of the parallel holes and additional exploration is needed to fully
understand the potential of these to contribute to a lower high-grade zone within a future resource estimate.
Approximately two kilometres southwest of Rincones, drilling at the Colla target cut a long interval with high cobalt starting close to surface, marking the best
cobalt interval at the project to date:
123.1m
at 443 g/t Co starting at
24.9 m
depth in drill hole SP-DDH-25.
Includes
19.43 m
at 790 g/t Co and 32.6 % Fe
Brian McEwen
, VP Exploration and Development for Golden Arrow, commented,
"The Company is extremely pleased with the results of the drill program so far.
We have succeeded in demonstrating that wide zones of mineralization are continuous between the previously defined north and south Rincones zones, within
a broad area that was not historically drilled. With half of the estimated 10,000 metre program remaining, we are confident that we will be further increasing the
resource potential of the project."
The six holes reported herein are part of the on-going 10,000-metre diamond drilling campaign at the San Pietro Iron-Copper-Gold-Cobalt Project in
Chile
("San
Pietro" or the "Project") announced on
April 24, 2024
, which is expected to provide data for the first Mineral Resource Estimate for the project. The program is
just over 50% complete, with additional drill holes in progress to expand the known mineralized zones at Rincones, and additional exploration drilling planned.
Table 1. Summary of Intervals, Rincones Phase 2 Drilling
[Cu Grade >0.20% or Co Grade >200 g/t or Au Grade >0.2 g/t or
Fe Grade
>30%]
Hole
From
(m)
To
(m)
Interval
(m)
Cu
(%)
Au
(g/t)
Co
(g/t)
Fe
(%)
SP-DDH-21
14.00
19.00
5.00
0.34
0.05
46
13.7
95.00
119.31
24.31
0.23
0.08
298
21.3
148.00
154.00
6.00
0.34
0.04
66
9.4
163.50
177.62
14.12
0.27
0.07
60
15.7
222.00
226.00
4.00
0.24
0.01
33
9.5
289.73
293.00
3.27
0.09
0.02
263
13.8
295.00
303.00
8.00
0.56
0.07
160
7.2
329.00
353.00
24.00
0.04
0.08
439
10.6
358.00
366.00
8.00
0.06
0.05
315
31.6
386.00
402.00
16.00
0.02
0.07
345
10.2
408.00
419.60
11.60
0.32
0.03
89
7.0
443.44
446.50
3.06
0.28
0.04
94
8.8
SP-DDH-22
22.00
32.00
10.00
0.21
0.05
93
10.2
104.35
111.53
7.18
0.95
0.08
78
12.
158.00
268.00
110.00
0.40
0.08
85
18.0
including
216.00
232.90
16.90
1.38
0.20
210
16.8
with
231.78
232.90
1.12
10.35
2.44
470
23.1
and including
258.00
268.00
10.00
0.22
0.05
192
47.0
326.00
328.00
2.00
1.35
0.16
176
15.8
SP-DDH-23
133.11
137.87
4.76
2.56
1.04
317
27.5
172.63
180.00
7.37
0.25
0.02
68
11.3
SP-DDH-24
151.45
156.85
5.40
0.25
0.03
140
12.8
SP-DDH-25
24.90
148.00
123.10
0.03
0.04
443
18.2
including
26.00
44.70
18.70
0.06
0.06
721
23.1
and including
126.57
146.00
19.43
0.02
0.10
790
32.6
169.88
172.20
2.32
0.03
0.07
453
16.2
SP-DDH-26
156.00
157.37
1.37
0.46
0.04
151
10.9
Notes: Intervals are downhole length. See hole descriptions in text for additional details.
San Pietro Phase 2 Drill Program Details
The San Pietro Project hosts multiple targets with strong Iron oxide-Copper-Gold and Cobalt (IOCG+cobalt) mineralization (see Figure 1). This mineralization is
typically found within a pile of fine to porphyritic andesites that exhibit widespread potassic feldspar alteration. The mineralization is often associated with areas
where a superimposed quartz-scapolite alteration is more intense and there is a development of brecciation and massive replacement of magnetite.
In 2023, the Company completed a Phase 1 drill program of approximately 4000 metres of diamond drilling in 13 holes to add to the database of ~34,000 metres
of historic drilling at San Pietro. Strongly mineralized intervals were intercepted at all targets tested as reported in company news releases on
June 13
,
June 27
and
July 12
, 2023.
The Company is concentrating this Phase 2 drill program mainly on the Rincones advanced exploration target with the goal of completing an initial Mineral
Resource Estimate. In addition, approximately 3,000 metres of drilling has been earmarked to test for new mineralization at other high-potential target areas
throughout the Project.
Rincones Target Drilling
SP-DDH-21
SP-DDH-21 was drilled in a gap at the western side of the central Rincones target and successfully increased the known mineralization between the better-
defined Rincones north and south areas.
The hole was a 260 metre step-out to the northeast of Phase 1 hole SP-DDH-11, which was reported on
July 12, 2023
. SP-DDH-11 was well-mineralized
throughout the hole, with 13 intervals reported between
68m
and
426m
depth. As shown in Table 1, SP-DDH-21 was similarly well mineralized throughout the hole
with twelve intervals reported above cutoffs, and modeling indicates correlation with some of the manto units as show in
Figure 3
.
Copper-cobalt-iron mineralization in SP-DDH-21 is associated with strong quartz-scapolite alteration in crackle breccias and massive magnetite. Breccias with up
to 6% of pyrite show high cobalt mineralization as seen in the reported intervals between 289 and 402 metres in Table 1.
SP-DDH-22
This hole confirms the continuity of mineralization between Phase II drill holes SP-DDH-14 (
135 m
to the west) and SP-DDH-19 (
155 m
to the east) as shown in
Figure 2
. SP-DDH-22 shows a wide mineralized interval of
110 m
starting at
158 m
deep, (see Table 1) including a higher-grade interval of
1.12 m
with 10.35%
Cu, 2.44 g/t Au, 132 g/t Co and 25.7% Fe where the core contained patches of massive chalcopyrite-pyrite. This long interval correlates with the 101.38-metre
mineralized interval reported in drill hole SP-DDH-19 that averaged 0.43% Cu, 177 g/t Co and 30.1% Fe which also includes a higher-grade interval of
5.0m
with
1.3% Cu; 0.29 g/t Au, 253 g/t Co and 27.4% Fe (see News Release dated
August 8, 2024
).
In addition, anomalous molybdenum values were noted in both SP-DDH-19 and SP-DDH-22. The 110 mineralized metres starting at
158 m
deep in hole SP-DDH-
22 averaged 139 g/t Mo, and core logging noted the presence of veinlets of molybdenite. In SP-DDH-19 the 101.38 metre interval noted above averaged 147 g/t
Mo. The importance of this molybdenum mineralization is under evaluation, but it is present in most of the drillholes in the eastern part of the Rincones target.
SP-DDH-23, SP-DDH-24 and SP-DDH-26
These three drillholes were drilled in the northern and eastern part of Rincones testing the edge of a large magnetic anomaly that has guided much of the recent
drilling. Results confirm the strong association between the high magnetics and mineralization. Drill hole SP-DDH-23 intercepted one high-grade interval of
4.76 m
with 2.56% Cu, 1.04 g/t Au, 317 g/t Co and 27% Fe, with strong replacement of the andesite by magnetite and with chalcopyrite and pyrite both disseminated and
in veinlets. Hole SP-DDH-24, drilled to south, intercepted several veins and breccias with specularite-calcite-quartz-chalcopyrite. Finally, drillhole SP-DDH-26
shows weak scapolite-quartz alteration and some specularite breccias with limited copper mineralization.
Colla Target Drilling
SP-DDH-25
This hole was drilled
160 m
north of SP-DDH-09. The objective was to test the continuity of mineralization in specularite breccias drilled in SP-DDH-09, which
returned an interval of
11.25m
averaging 483 g/t Co starting at
130.55m
depth (see News Release
June 13
th
, 2023
). That interval is believed to be part of the
same breccia body as drilled in CO11DH-002, located 485 metres to the south, which hosted the best historic cobalt interval at the project: 414 ppm Co over
32
m
starting at
116 m
downhole. Hole SP-DDH-25 was intended to intercept the same mineralized structure closer to surface. The hole was a success and the
structure in this location was significantly wider than in SP-DDH-09, returning a new best cobalt intercept for the project of
123.1 m
with 443 g/t Co and 18.2 % Fe
starting at 24.9 metres deep (see
Figure 4
). This drill hole together with the surface geochemistry confirm that the Colla target is a significant near-surface
(outcropping) high cobalt target.
Table 2. Drill Hole Collar Information
[PSAD 56 / UTM Zone 19 S]
Hole
Easting
Northing
Elevation
(m)
Azimuth (˚)
Dip
Final
Depth (m)
(˚)
SP-DDH-21
390809
7071811
996
40
-60
461
SP-DDH-22
391267
7071769
943
20
-65
341
SP-DDH-23
391466
7072416
923
20
-70
208.9
SP-DDH-24
391465
7072386
923
200
-68
353
SP-DDH-25
390119
7069878
1127
270
-60
185
SP-DDH-26
391442
7071603
923
20
-65
261.5
Methodology & QA/QC
This drilling campaign was completed by Sociedad de Servicios Andinos SpA of Copiapó,
Chile
, using diamond drill producing HQ-sized core. The Golden Arrow
field team, supervised by senior geologists, photographed and logged the entire length of core for each drillhole, as well as measured it for recovery and marked
it for sampling. Pieces of whole core approximately 10 to 15 cm long were selected and measured for specific gravity on average every 20 metres and targeting
all different lithologies. Subsequently, the core was cut in half with an electric saw. One half was labelled, bagged and sent for analysis and the other half retained
onsite. After completing the sampling of each hole, the samples were shipped to ALS Laboratory in Copiapo,
Chile
by a contract truck service. Sample
preparation and gold analysis by Fire Assay and reading by atomic absorption on 30 gm sample by method Au-AA23 was completed at the ALS facility in
Santiago
de
Chile
. Multi-element package by ICP-OES reading following a four-acid digestion by method ME-ICP61 was performed at ALS facilities in
Lima,
Peru
. Samples with over limits in copper (+ 10,000 ppm) were re-assayed by ore grade method Cu-OG62 that includes four acid digestion and ICP-OES reading.
The Company follows industry standard procedures for the work carried out on the San Pietro Project, with a quality assurance/quality control (QA/QC) program.
Blank and standard samples were inserted in each batch of samples sent to the laboratory for analysis. Golden Arrow detected no significant QA/QC issues
during review of the data. The trajectory of all the holes drilled at San Pietro during this Phase 2 were measured using the gyroscope equipment "Champ
Navigator" that assures no interference from the magnetite in the ground. Additionally, all the core was orientated using the "Champ Ori" core orientator to
measure the azimuth and dip of structures.
About the San Pietro IOCG Project
The San Pietro Project covers 19,200 hectares, approximately 100 kilometres north of Copiapo. Situated between and adjacent to Capstone Copper's Manto
Verde Mine property and Santo Domingo Project, San Pietro is in the centre of a potential new copper-iron-cobalt district within an active, well-developed mining
region that is home to all the major iron oxide-copper-gold ("IOCG") deposits in
Chile
.
The Project is hosted by andesite units in a Cretaceous-aged volcano-sedimentary sequence associated with intrusive rocks including granodiorites and diorites of
similar age. The Project is located east of the Atacama Fault system, a major north-south regional structure, which was instrumental in controlling the
emplacement of the ore deposits in the area.
Mineralization at San Pietro is typical of an IOCG system, with the addition of cobalt, and occurs in mantos, breccias and veins within a zone of alteration
characterized by an association of actinolite, epidote, chlorite and scapolite. The mantos are replacement of andesite by magnetite and sulphides, with a roughly
southeast strike and a gentle dip to the SW. Breccias and veins crosscut the mantos, are often subvertical, and filled with specularite and sulphides.
Qualified Persons
The exploration programs are designed by the Company's geological staff and results are reviewed, verified (including sampling, analytical and test data) and
compiled under the supervision of
Brian McEwen
, P.Geol., VP Exploration and Development to the Company. Mr. McEwen is a Qualified Person as defined in
National Instrument 43-101 and has reviewed and approved the contents of the news release.
About Golden Arrow:
Golden Arrow Resources Corporation is a mining exploration company with a successful track record of creating value by making precious and base metal
discoveries and advancing them into exceptional deposits.
Golden Arrow is actively exploring its flagship property, the advanced San Pietro iron oxide-copper-gold-cobalt project in
Chile
, and a portfolio that includes nearly
125,000 hectares of prospective properties in
Argentina
.
The Company is a member of the Grosso Group, a resource management group that has pioneered exploration in
Argentina
since 1993.
ON BEHALF OF THE BOARD
"Joseph Grosso"
_______________________________
Mr.
Joseph Grosso
,
Executive Chairman, President and CEO
Neither the TSXV nor its Regulation Services Provider (as that term is defined in policies of the TSXV) accepts responsibility for the adequacy or accuracy of
this release.
This news release contains forward-looking statements. Generally, forward-looking statements can be identified by the use of terminology such as "anticipate",
"will", "expect", "may", "continue", "could", "estimate", "forecast", "plan", "potential" and similar expressions. Forward-looking statements address future events
and conditions and therefore involve inherent risks and uncertainties. All statements, other than statements of historical fact, that address activities, events or
developments management of the Company believes, expects or anticipates will or may occur in the future, including, without limitation, statements about the
Company's plans for its mineral properties; the Company's business strategy, plans and outlooks; the future financial or operating performance of the
Company; and future exploration and operating plans are forward-looking statements.
Forward-looking statements are subject to a number of risks and uncertainties that may cause the actual results of the Company to differ materially from those
discussed in the forward-looking statements and, even if such actual results are realized or substantially realized, there can be no assurance that they will have
the expected consequences to, or effects on, the Company. Accordingly, readers should not place undue reliance on the forward-looking statements. Factors
that could cause actual results or events to differ materially from current expectations include, among other things: risks and uncertainties related to the ability
to obtain, amend, or maintain licenses, permits, or surface rights; risks associated with technical difficulties in connection with exploration activities; the
possibility that future exploration. There may be other factors that cause results or events to not be as anticipated. Actual results may differ materially from
those currently anticipated in such statements. Readers are encouraged to refer to the Company's Management's Discussion and Analysis for a more detailed
discussion of factors that may impact expected future results. The forward-looking statements contained in this press release are made as of the date hereof or
the dates specifically referenced in this press release, where applicable. The Company undertakes no obligation to publicly update or revise any forward-
looking statements, unless required pursuant to applicable laws. All forward-looking statements contained in this press release are expressly qualified by this
cautionary statement.
We advise U.S. investors that the SEC's mining guidelines strictly prohibit information of this type in documents filed with the SEC. U.S. investors are cautioned
that mineral deposits on adjacent properties are not indicative of mineral deposits on our properties.
View original content to download multimedia:
https://www.prnewswire.com/news-releases/golden-arrow-continues-to-intersect-thick-zones-of-copper-and-of-cobalt-mineralization-at-the-san-pietro-iron-copper-gold-cobalt-project-chile-302243020.html
SOURCE
Golden Arrow Resources Corporation
View original content to download multimedia:
http://www.newswire.ca/en/releases/archive/September2024/10/c9014.html
%SEDAR: 00042897E
For further information:
For further information, please contact: Corporate Communications, Tel: 1-604-687-1828, Toll-Free: 1-800-901-0058, Email:
CO: Golden Arrow Resources Corporation
CNW 07:00e 10-SEP-24