Discovery Continues to Demonstrate Expansion Potential in Final Phase 2 Drill Holes at Cordero
Discovery Continues to Demonstrate Expansion Potential in Final
Phase 2 Drill Holes at Cordero
September 28, 2022, Toronto, Ontario - Discovery Silver Corp. (TSX-V: DSV, OTCQX:
DSVSF) (“Discovery” or the “Company”) is pleased to announce results of the final 26 drill
holes from its Phase 2 drill program on its flagship Cordero silver project (“Cordero” or “the
Project”) located in Chihuahua State, Mexico. These holes consisted of upg rade and
expansion drilling of the PEA pit and expansion drilling of the 2021 resource pit. Drilling will be
used to support a Pre-Feasibility Study (“PFS”) planned for early 2023. The Company is also
pleased to provide an update on its ongoing exploration program on its property wide targets.
Highlight intercepts from Phase 2 drilling include:
• 58 m averaging 208 g/t AgEq1 (99 g/t Ag, 0.33 g/t Au, 1.6% Pb and 1.0% Zn) from 78 m
and 48 m averaging 231 g/t AgEq1 (100 g/t Ag, 0.63 g/t Au, 1.8% Pb and 0.8% Zn) from
148 m in hole C22-614. These intercepts were from upgrade drilling within the PEA starter
pit.
• 125 m averaging 111 g/t AgEq1 (37 g/t Ag, 0.04 g/t Au, 0.4% Pb and 1.6% Zn) from 265
m in hole C22- 644. This intercept was directly below the 2021 resource pit in an area
previously modeled as waste.
• 42 m averaging 201 g/t AgEq1 (76 g/t Ag, 0.06 g/t Au, 1.0% Pb and 2.4% Zn) from 453
m in hole C22-634. This interval is located approximately 20 m below the resource pit.
• 86 m averaging 120 g/t AgEq1 (32 g/t Ag, 0.02 g/t Au, 0.1% Pb and 2.2% Zn) from 716
m in hole C22-636, highlighting the mineralization potential at depth.
Tony Makuch, Interim CEO, states: “The completion of our Phase 2 drill program , consisting
of close to 80,000 m in over 250 drill holes, represents another major milestone in the
advancement of our Cordero project. This program consistently intercepted mineralization
beneath and to the northeast of the open pit outlined in last year’s Preliminary Economic
Assessment highlighting the potential to expand the size of the open pit in our upcoming PFS.
“Our PFS is now expected to be completed in early 2023, a slight delay from our original target
of mid to late 4Q 2022. The additional time will allow us to further optimise the study to
incorporate recent positive metallurgical developments including the s treamlining of the
process circuit via co-processing of oxides and sulphides and cost efficiencies through lower
reagent consumption and a coarse grind size.”
NEWS RELEASE
DRILL RESULTS:
This final set of Phase 2 drill holes was focused on two main areas: 1) upgrade and expansion
drilling of the PEA open pit; and 2) expansion drilling of the resource at depth in the northeast
of the deposit. R esults will be incorporated in a resource update and PFS scheduled for
completion in the first quarter of 2023.
Plan maps summarizing the drilling completed since the 2021 PEA can be found at the
following link: PEA vs PFS drill hole plan maps
Detailed drill highlights from the holes in this release are provided in the tables below.
Supporting maps and sections, drill hole locations and full assay results can be found at the
following link: Plan map, sections & assays
A PDF of this release with supporting maps and sections included as appendices can be
found at the following link: Press release with plan map & sections
PEA Pit Upgrade & Expansion Drilling
Resource upgrade drilling in the PEA starter pit (Pozo de Plata zone) continue to confirm the
excellent continuity of near-surface high-grade mineralization. Highlight intercepts include 58.3
m of 208 g/t AgEq 1 from 78.1 m, 48.3m of 231 g/t AgEq 1 from 147.6 m (both intercepts from
C22-614) and 50.0 m of 109 g/t AgEq1 from 140.0 m (C22-613).
Drilling beneath the PEA pit in the northeast of the deposit returned a number of excellent
intercepts highlighting the potential to expand the open pit for the upcoming PFS. Examples
include 61.1m of 123 g/t AgEq1 approximately 50 m below the PEA pit in hole C22- 637, 65.3
m of 121 g/t AgEq1 approximately 100 m below the PEA pit in hole C22-615 and 46.7 m of 108
g/t AgEq1 approximately 100 m below the PEA pit in hole C22-645.
Detailed drill highlights from the open pit upgrade and expansion drilling are provided in the
table below:
Hole ID From
(m)
To
(m)
Width
(m)
Ag
(g/t)
Au
(g/t)
Pb
(%)
Zn
(%)
AgEq1
(g/t)
C22-613 140.0 190.0 50.0 58 0.21 0.7 0.4 109
C22-614 78.1 136.4 58.3 99 0.33 1.6 1.0 208
and 147.6 195.9 48.3 100 0.63 1.8 0.8 231
C22-615 322.7 388.0 65.3 53 0.07 0.7 1.1 121
C22-618 106.1 165.3 59.2 42 0.03 0.9 1.0 110
and 274.2 347.4 73.2 47 0.07 0.3 0.2 68
C22-634 452.9 495.1 42.2 76 0.06 1.0 2.4 201
C22-637 18.3 33.7 15.4 50 0.07 1.0 1.8 153
and 128.9 189.9 61.1 37 0.05 0.9 1.5 123
1See supporting technical disclosure underneath the second table below.
Resource Expansion Drilling
Drilling continues to be successful in demonstrating the continuity of mineralization beneath
the resource pit constraint highlighting the potential to expand the resource at depth in the
northeast of the deposit. In the South Corridor, C22 -644 intercepted a broad zone of higher -
grade mineralization starting at the edge of the resource pit that returned 124.7 m of 111 g/t
AgEq1. This area of the deposit was previously modeled as waste. In the North Corridor, C22-
634 intercepted 42.2 m of 201 g/t AgEq1 approximately 20 m below the resource pit constraint.
Drilling also continues to intercept broad zones of mineralization at significant depths that
correlate with the deep feeder structures of the mineralized system at Cordero. Examples from
the drill holes in this press release include C22 -637, which returned 86.4m of 120 g/t AgEq 1
from 716.4 m and C22-625, which returned 40.6m of 97 g/t AgEq1 from 721.1 m.
Detailed drill highlights from the resource expansion drilling are provided in the table below:
Hole ID From
(m)
To
(m)
Width
(m)
Ag
(g/t)
Au
(g/t)
Pb
(%)
Zn
(%)
AgEq1
(g/t)
C22-638 89.2 168.9 79.7 37 0.03 0.7 1.0 97
and 179.9 232.2 52.3 21 0.02 0.5 0.7 63
C22-641 259.9 300.0 40.2 75 0.14 1.2 1.5 178
C22-643 222.2 243.7 21.5 81 0.09 1.2 1.1 164
including 510.3 536.6 26.3 26 0.05 0.3 2.9 147
C22-644 264.8 389.5 124.7 37 0.04 0.4 1.6 111
C22-645 115.5 157.2 41.8 47 0.04 0.9 1.0 113
and 234.6 270.7 36.1 47 0.05 0.8 0.4 88
and 354.6 401.3 46.7 52 0.04 0.7 0.8 108
Hole ID From
(m)
To
(m)
Width
(m)
Ag
(g/t)
Au
(g/t)
Pb
(%)
Zn
(%)
AgEq1
(g/t)
C22-621 326.7 384.8 58.2 21 0.05 0.2 1.0 70
and 723.8 776.0 52.2 15 0.02 0.1 1.4 71
C22-625 61.7 79.0 17.3 25 0.12 0.3 3.1 161
and 325.9 355.9 30.0 24 0.02 0.2 1.9 102
and 721.1 761.7 40.6 35 0.07 0.0 1.5 97
C22-629 224.5 272.0 47.6 30 0.08 0.3 0.8 74
and 304.1 327.8 23.7 29 0.08 0.4 0.7 72
and 634.1 662.3 28.3 17 0.02 0.1 1.7 86
C22-634 452.9 495.1 42.2 76 0.06 1.0 2.4 201
C22-637 0.0 42.9 42.9 34 0.03 0.6 0.7 81
1All results in this news release are rounded. Assays are uncut and undiluted. Widths are drilled widths, not true widths, as a full
interpretation of the actual orientation of mineralization is not complete. As a guideline, intervals with disseminated mineralization
were chosen based on a 25 g/t AgEq cutoff with no more than 10 m of dilution. AgEq calculations are used as the basis for total
metal content calculations given Ag is the dominant metal constituent as a percentage of AgEq value in approximately 70% of the
Company’s mineralized intercepts. AgEq calculations for reported drill results are based on USD $22.00/oz Ag, $1, 600/oz Au,
$1.00/lb Pb, $1.20/lb Zn. The calculations assume 100% metallurgical recovery and are indicative of gross in-situ metal value at
the indicated metal prices. Refer to Technical Notes below for metallurgical recoveries assumed in the 2021 PEA completed on
Cordero.
PROPERTY WIDE EXPLORATION:
Surface exploration work has been ongoing at Cordero since March 2021. Work completed to
date includes geological mapping, surface rock and soil sampling, geophysics and diamond
drilling. In total results from 2,190 surface rock samples and 3,639 soil samples have been
received. An additional 1,508 soil samples are pending results. The surface work is based on
historical data including soil geochemistry, structural and alteration interpretations of satellite
imagery, induced polarization (“ IP”) geophysics surveys and an airborne magnetometry
(“Mag”) and electromagnetic (“EM”) geophysical survey completed by the Company in 2019.
The five main surface exploration target areas based on this work are Sanson, Porfido Norte,
Dos Mil Diez, Molino de Viento, and La Perla. Discovery so far has completed preliminary
reconnaissance-style drilling at Sanson and Porfido Norte consisting of 10 drill holes totaling
4,500 m. A map showing the location of these five target areas can be found at the following
link: Property wide targets
At Sanson, located two kilometres northeast of the main resource area, seven drill holes have
been completed. Drill targeting was based on surface alteration, a magnetic anomaly indicating
a proximal intrusive body, and surface mapping of intrusive rocks and breccias. Six of the
holes intersected very strongly silicified and sericite- altered rhyodacite, breccias and
sedimentary rocks with traces of quartz-molybdenite veining that returned anomalous levels of
molybdenum (100 – 400 ppm) and silver (260 – 270 ppm).
At Porfido Norte, three drill holes were completed following s urface mappi ng and rock
sampling. Historic IP geophysics indicated the presence of an intrusive body at depth and
mapping identified several intrusive sills at surface. Drilling intersected sparse, very narrow
(<10cm) mineralized sulphide veins within the intrusive rocks that returned anomalous Ag, Au,
and Zn values. Further work at Sanson and Porfido Norte will be evaluated following the
completion of the current exploration program across all five property-wide targets.
At Dos Mil Diez, at the southwest edge of the Cordero deposit, surface mapping and sampling
has identified a number of rhyodacite intrusive sills and dikes hosted by calcareous
sedimentary rock s similar to those present at Cordero. Surface sampling has returned
anomalous values of Ag, Pb, and Zn with in narrow sulphide veins, including a 10 cm galena
Hole ID From
(m)
To
(m)
Width
(m)
Ag
(g/t)
Au
(g/t)
Pb
(%)
Zn
(%)
AgEq1
(g/t)
and 716.4 802.8 86.4 32 0.02 0.1 2.2 120
C22-644 264.8 389.5 124.7 37 0.04 0.4 1.6 111
vein that returned 2,530 g/t Ag. The typical strike extent of the veins is approximately 10 to 20
m. Drill hole planning is in its final stages for this area.
At Molino de Viento, located ten km southwest of the main Cordero resource, surface mapping
and sampling returned elevated Zn values that may coincide with an intrusive body at depth
based on the 2019 Mag and EM survey. Drill targets are currently being finalised for this area
and will incorporate a recently completed 15,200 m 2D IP survey that supplements the historic
geophysical data.
The La Perla target is located approximately 10 km south of the Cordero deposit. Historic work
includes an IP survey (16,500m) and a four-hole, 1,380 m drill program. The Company has
also completed surface mapping and sampling across the target area . The IP geophysical
survey identified weak chargeability anomalies at depth and historic drilling intersected
sulphide veins with anomalous Ag, Pb, and Zn values as well as wider intervals of mineralized
rhyolite in hole C12-247 that returned 12.0 m averaging 28 g/t Ag from surface and 174.2 m
averaging 4 g/t Ag and 0.13% Zn from 38.0 m. Additional IP geophysics survey lines are
currently being completed to assist with finalizing drill targets.
DRILL PROGRAM UPDATE:
The Company has now completed its Phase 2 drill program. This drill program along with all
previous drilling is summarized in the table below . Feasibility study drilling has already
commenced and will consist of engineering drilling, resource upgrade drilling and drilling
targeting the expansion of the PFS open pit. The total metres to be drilled in the feasibility
study drill program will be finalised following the completion of the PFS.
Drill Program Period Drill Metres Drill Holes
Historic 2009 – 2017 123,000 m 253
Discovery Silver – Phase 1 2019 – 2021 92,000 m 225
Discovery Silver – Phase 2 2021 – 2022 78,000 m 257
TOTAL 293,000 m 735
About Discovery
Discovery’s flagship project is its 100%-owned Cordero project, one of the world’s largest silver
deposits. The PEA completed in November 2021 demonstrates that Cordero has the potential
to be developed into a highly capital efficient mine that offers the combination of margin, size
and scaleability. Cordero is located close to infrastructure in a prolific mining belt in Chihuahua
State, Mexico. Continued exploration and project development at Cordero is supported by a
strong balance sheet with cash of approximately C$60 million.
On Behalf of the Board of Directors,
Tony Makuch, P.Eng
Interim CEO
For further information contact:
Forbes Gemmell, CFA
VP Corporate Development
Phone: 416-613-9410
Email: [email protected]
Website: www.discoverysilver.com
Sample analysis and QA/QC Program
The true width of the veins is estimated to be approximately 70% of the drilled width. Assays
are uncut except where indicated. All core assays are from HQ drill core unless stated
otherwise. Drill core is logged and sampled in a secure core storage facility located at the
project site 40km north of the city of Parral. Core samples from the program are cut in half,
using a diamond cutting saw, and are sent to ALS Geochemistry -Mexico for preparation in
Chihuahua City, Mexico, and subsequently pulps are sent to ALS Vancouver, Canada, which
is an accredited mineral analysis laboratory, for analysis. All samples are prepared using a
method whereby the entire sample is crushed to 70% passing -2mm, a split of 250g is taken
and pulverized to better than 85% passing 75 microns. Samples are analyzed for gold using
standard Fire Assay-AAS techniques (Au-AA24) from a 50g pulp. Over limits are analyzed
by fire assay and gravimetric finish. Samples are also analyzed using thirty three- element
inductively coupled plasma method (“ME -ICP61”). Over limit sample values are re -assayed
for: (1) values of zinc > 1%; (2) values of lead > 1%; and (3) values of silver > 100 g/t. Samples
are re-assayed using the ME-OG62 (high-grade material ICP-AES) analytical package. For
values of silver greater than 1,500 g/t, samples are re -assayed using the Ag- CON01
analytical method, a standard 30 g fire assay with gravimetric finish. Certified standards and
blanks are routinely inserted into all sample shipments to ensure integrity of the assay
process. Selected samples are chosen for duplicate assay from the coarse reject and pulps
of the original sample. No QAQC issues were noted with the results reported herein.
Qualified Person
Gernot Wober, P.Geo, VP Exploration, Discovery Silver Corp., is the Company's designated
Qualified Person for this news release within the meaning of National Instrument 43 -101
Standards of Disclosure for Mineral Projects (“NI 43-101”) and has reviewed and validated that
the information contained in this news release is accurate.
TECHNICAL NOTES & FORWARD-LOOKING STATEMENTS:
The most recent technical report for the Cordero Project is the 2021 Preliminary Economic
Assessment (PEA) . The PEA was completed by Ausenco Engineering Canada Inc. with
support from AGP Mining Consultants Inc. and Knight Piésold and Co. (USA). The full technical
report supporting the PEA is available on Discovery’s website and on SEDAR under Discovery
Silver Corp.
The PEA assumed average life-of-mine recovery assumptions for sulphide material of 84% for
Ag, 19% for Au, 86% for Pb and 85% for Zn. The PEA assumed oxide recovery assumptions
of 56% for Ag and 63% for Au for crushed feed and 36% for Ag and 35% for Au for uncrushed
ROM feed.
Neither TSX Venture Exchange nor its Regulation Services Provider (as that term is defined in policies of the TSX Venture
Exchange) accepts responsibility for the adequacy or accuracy of this release.
This news release is not for distribution to United States newswire services or for dissemination in the United States.
This news release does not constitute an offer to sell or a solicitation of an offer to buy nor shall there be any sale of any of the
securities in any jurisdiction in which such offer, solicitation or sale would be unlawful, including any of the securities in the United
States of America. The securities have not been and will not be registered under the United States Securities Act of 1933, as
amended (the “1933 Act”) or any state securities laws and may not be offered or sold within the United States or to, or for account
or benefit of, U.S. Persons (as defined in Regulation S under the 1933 Act) unless registered under the 1933 Act and applicable
state securities laws, or an exemption from such registration requirements is available.
Cautionary Note Regarding Forward-Looking Statements
This news release may include forward- looking statements that are subject to inherent risks and uncertainties. All statements
within this news release, other than statements of historical fact, are to be considered forward looking statements. Forward-looking
statements including, but not limited to Discovery’s future plans and objectives regarding the Cordero Project and the prospect of
further discoveries there, which constitute forward looking information that involve various risks and uncertainties . Although
Discovery believes the expectations expressed in such forward-looking statements are based on reasonable assumptions, such
statements are not guarantees of future performance and actual results or developments may differ materially from those
described in forward- looking statements. Factors that could cause actual results to differ materially from those described in
forward-looking statements include fluctuations in market prices, including metal prices, continued availability of capital and
financing, and general economic, market or business conditions. There can be no assurances that such statements will prove
accurate and, therefore, readers are advised to rely on their own evaluation of such uncertainties. Discovery does not assume
any obligation to update any forward-looking statements except as required under applicable laws.