STAR – Orion South Diamond Project Preliminary Results from First Bulk Sample Trench Confirm Previous Sampling Grades: 2,517 Diamonds Weighing 120.1 Carats Recovered
NEWS RELEASE August 04, 2020
Stock Symbol: DIAM: TSX Saskatoon, Saskatchewan
STAR – ORION SOUTH DIAMOND PROJECT
PRELIMINARY RESULTS FROM FIRST BULK SAMPLE TRENCH CONFIRM PREVIOUS
SAMPLING GRADES: 2,517 DIAMONDS WEIGHING 120.1 CARATS RECOVERED
Star Diamond Corporation (“Star Diamond” or the “Corporation” ) announces that a total of 2,517 diamonds
weighing 120.1 carats have been recovered from the first bulk sample trench (19FALCT001) excavated on the Star
Kimberlite. These results are from the first of ten bulk sample trenches that were excavated by Rio Tinto Exploration
Canada Inc. (“RTEC”) in 2019 (see News Release s dated June 3, and October 8, 2019) . The breakdown of the
kimberlite intercepted, and diamonds recovered from trench 19FALCT001, are detailed in Table 1 below.
The average diamond grade from this first trench is similar to historical diamond grade results detected from the
underground bulk sampling and large diameter drilling (“LDD”) completed on the Star Kimberlite between 2004 and
2009. These results are also similar to t he overall weighted average grade (14 cpht) reported in Star Diamond’s
Preliminary Economic Assessment (“PEA”) of the Star and Orion South kimberlites (the “Project”) (see News Release
dated April 16, 2018).
The three largest diamonds recovered are 3.27, 3.03 and 1.73 carats , respectively, and were all recovered from
Early Joli Fou (“EJF”) kimberlite. The EJF is the dominant kimberlite unit within the Project in terms of ore volume
and diamond grade. As further referenced below, there are indications that recent diamond breakage has occurred
in the diamond parcels recovered from 19FALCT001, suggesting that the extraction and/or processing systems being
used by RTEC may be resulting in diamond breakage. Comprehensive diamon d breakage studies will be required
to assess the nature and extent of the diamond breakage resulting from RTEC’s methods and the possibility that
larger diamonds would have been recovered absent such breakage.
Senior Vice President Exploration and Development, George Read, states: “The diamond results from 19FALCT001
provide an early assessment that the trench cutter bulk sampling method has the potential to replicate grades
similar to the previous underground bulk sampling and LDD performed by Star Diam ond on the Star Kimberlite.
Individual EJF kimberlite samples in this first trench exhibit a range of grades (4.88 to 23.34 cpht) , which are as
expected for the EJF kimberlite.”
To date, kimberlite material from four trenches (19FALCT001, 19FALCT00, 19FALCT003 and 19FALCT010) has been
processed by RTEC through the on -site Bulk Sample Plant (“BSP”), with concentrates forwarded to the
Saskatchewan Research Council (“SRC”) for final diamond recovery and reporting. Currently, only the diamond
results for the first trench have been fully reported to Star Diamond by the SRC. As reporting to Star Diamond on
the results from additional trenches is completed, Star Diamond looks forward to providing additional updates. Star
Diamond currently expects that all or substantially all of the bulk sample s from the ten sample trenches collected
during 2019 will be processed by RTEC during calendar 2020, provided that there are not any unexpected material
delays in this process including issues arising from COVID19.
Star Diamond also notes various ongoing issues arising from RTEC’s methods. RTEC is using several technologies
that have not, to the Corporation’s knowledge, previously been used in either bulk sample collecting or processing
involving similar projects. The purpose of applying these new technologies (including using a Bauer rig t o collect
bulk samples and using a Tomra XRT machine to improve diamond detection and to reduce the size of the samples
sent for final diamond recovery) was to improve the overall diamond grade and reduce diamond breakage. It
appears that, to date, the samples being sent to the SRC are much larger in volume than had been initially expected.
- 2 -
The sheer volume has caused problems. Further, some coarse (+6-25 millimetre) kimberlite material from the first
bulk sample trench (19FALCT001) remains unprocessed by RTEC. The future processing of this potentially diamond
bearing material is presently unknown to Star Diamond . As referenced above, an initial diamond examination by
the SRC also suggests that some recent diamond breakage has occurred in th e diamond parcels recovered from
19FALCT001. Comprehensive diamond breakage studies will be required as part of the assessment of both the
extraction and processing systems being used by RTEC and to determine the efficacy and impact of these systems
including diamond breakage.
Kimberlite was excavated from the first bulk sample trench (19FALCT001) between 111.0 and 228.4 metres below
the surface. As a result, RTEC sampled and processed some kimberlite units previously assessed by Star Diamond
as not contributing to the economics of the Project. The trench cutter has a rectangular profile of 3.250 metres by
1.575 metres (3.200 by 1.525 metres drill tool plus 25 millimetres all round overbreak). The trenches were
excavated using a Bauer BC 50 Cutter mounted on a Bauer MC 128 Duty -cycle Crane. Kimberlite excavated by the
cutter bit was pumped to the surface in a slurry, and kimberlite fragments between +1.0 and 80.0 millimetres were
recovered from the slurry by the Kimberlite Separation Unit (“KSU”). These kimberlite fragments were collected in
cubic metre bulk bags and kept in an on-site storage area by RTEC until such time, following a number of delays, as
RTEC’s BSP had been assembled and commissioned. Kimberlite heavy mineral concentrates and XRT Accepts
produced by the BSP a re being delivered by RTEC to the SRC ’s Geoanalytical Laboratories located in Saskatoon,
Saskatchewan for final diamond recovery.
Table 1. Diamond stone and grade results provided for each kimberlite type sampled in Trench 19FALCT001
Kimberlite1
Type
Kimberlite
Intercept
(metres)
Drilled2
Tonnes
Carats3
(+1 DTC)
Grade4
(cpht)
Stones
(+1 DTC)
Stones
per tonne
(+1 DTC)
Largest
Stone
(ct)
URVKU 111.00-116.85 56.89 0.61 1.07 29 0.51 0.02
LJF 116.85-146.04 261.45 6.24 2.39 289 1.11 0.21
MJF 146.04-157.70 109.82 3.58 3.26 168 1.53 0.07
EJF 157.70-228.44 778.24 109.67 14.09 2,031 2.61 3.27
Total 117.44 1,206.40 120.10 2,517 3.27
Notes
1. Kimberlite Types: URVKU Undifferentiated, reworked volcaniclastic kimberlite units; LJF: Late Joli Fou
Kimberlite; MJF: Mid Joli Fou Kimberlite; EJF: Early Joli Fou Kimberlite . The URVKU and the LJF were
not included in the Star Diamond PEA mineral resource estimate
2. The excavated tonnes are calculated using theoretical trench volumes and core pilot hole dry densities
provided by RTEC. These are equivalent to dry tonnes.
3. Commercial diamonds are defined as diamonds that will not pass through a +1 DTC screen, which has
round apertures of 1.09 millimetres
4. cpht: diamond grade in carats per hundred tonnes
Diamond results reported in this news release are based on diamond recovery processing conducted by SRC ’s
Geoanalytical Laboratories Diamond Services located in Saskatoon Saskatchewan. Primary recovery processing
consisted of X-ray transmission (XRT) sorting, magnetic separation and grease table recovery methods. Secondary
processing consisted of magnetic separation, grease table, X-ray luminescence (XRL) sorting and caustic fusion. SRC
is an independent mineral processing facility which is accredited to the ISO/IEC 17025:2017 standard by the
Standards Council of Canada as a testing laboratory for specific tests.
- 3 -
About Star Diamond Corporation
Star Diamond Corporation is a Canadian based corporation engaged in the acquisition, exploration and
development of mineral properties. Shares of the Corporation trade on the Toronto Stock Exchange under the
trading symbol “DIAM”. The Corporation’s Fort à la Corne kimberlites (including the Star - Orion South Diamond
Project) are located in central Saskatchewan in close proximity to established infrastructure, including paved
highways and the electrical power grid, which provide significant advantages for future mine development.
All technical information in this press release has been prepared under the supervision of George Read, Senior Vice-
President of Exploration and Development, a registered Professional Geoscientist in the Provinces of Saskatchewan
and British Columbia and Mark Shimell, Project Manager, a registered Professional Geoscientist in the Province of
Saskatchewan, who are the Corporation’s “Qualified Persons” under the definition of NI 43-101.
Caution Regarding Forward-Looking Statements
This news release contains forward -looking statements as defined by certain securities laws, including the "safe harbour" provisions of
Canadian securities legislation and the United States Private Securities Litigation Reform Act of 1995. Forward -looking information is often,
but not always, identified by the use of words such as "anticipate", "believe", "expect", "plan", "intend", "forecast", "targ et", "project",
"guidance", "may", "will", "should", "could", "estimate", "predict" or similar words suggesting future outcomes or language suggesting an
outlook. In particular, statements regarding the Corporation's future operations, future exploration and development activities or oth er
development plans constitute forward-looking statements. By their nature, statements referring to mineral reserves, mineral resources or
PEA constitute forward-looking statements. Forward-looking statements contained or implied in this press release include, but are not limited
to, the Corporation’s expectations regarding the processing and analysis of , and reporting of results from, the bulk samples previously
collected by RTEC and the timeline for doing so.
These forward-looking statements are based on the Corporation's current beliefs as well as assumptions made by and information currently
available to it and involve inherent risks and uncertainties, both general and specific.
Risks exist that forward -looking statements will not be achieved due to a number of factors including, but not limited to, developments in
world diamond markets, changes in diamond prices, risks relating to fluctuations in the Canadian dollar and other currencies relative to the
US dollar, changes in exploration, development or mining plans due to exploration results and changing budget priorities of RTEC or the
Corporation, risks related to the legal proceedings commenced by the Corporation against RTEC , including the determination of the
Corporation’s pending injunction application by the Court, the effects of competition in the markets in which Star Diamond operates, the
impact of the COVID -19 pandemic, risks related to the operation of the BSP and the processing methods being used by RTEC and the
effectiveness thereof, the impact of changes in the laws and regulations regulating mining exploration, development, closure, judicial or
regulatory judgments and legal proceedings, operational and infrastructure risks and the additional risks described in the Corporation's most
recently filed Annual Information Form, annual and interim MD&A , news releases and technical reports. The Corporation's an ticipation of
and success in managing the foregoing risks could cause actual results to differ materially from what is anticipated in such forward -looking
statements.
Although management considers the assumptions contained in forward-looking statements to be reasonable based on information currently
available to it, those assumptions may prove to be incorrect. When making decisions with respect to the Corporation, investor s and others
should not place undue reliance on these statements and should carefully consider the foregoing factors and other uncertainties and
potential events. Unless required by applicable securities law, the Corporation does not undertake to update any forward-looking statement
that is made herein.
For further information: [email protected] or (306) 664-2202
www.stardiamondcorp.com
- END -