Copper Fox Provides Analytical Results from 2024 Geotechnical Drilling Program at Schaft Creek Project
DR
COPPER FOX PROVIDES ANALYTICAL RESULTS FROM 2024
GEOTECHNICAL DRILLING PROGRAM AT SCHAFT CREEK PROJECT
Calgary, Alberta – January 16, 2025. Copper Fox Metals Inc. (“Copper Fox” or the “Company”) (TSXV:CUU
| OTCQX:CPFXF | FRA:HPU) is pleased to provide the analytical results for the six (6) geotechnical drillholes
completed at the Schaft Creek project in 2024. The Schaft Creek project is managed through the Schaft Creek Joint
Venture (SCJV). Teck Resources Limited (Teck) is the Operator of the SCJV and holds a 75% interest with Copper
Fox holding the remaining 25% interest. The Schaft Creek deposit, located in northwestern British Columbia , is
one of the largest undeveloped porphyry copper deposits in North America that contains significant gold -
molybdenum-silver by-products.
In 2024, the SCJV approved a C$1 8.9 million budget to advance key project activities including the collection of
geotechnical, metallurgical, engineering, and environmental data and community engagement. The geotechnical
drillholes were designed to collect additional geomechanical, downhole geophysical, structural, and
hydrogeological data to be used to generate updated deposit scale hydrogeological and slope stability models. Three
of the six geotechnical drillholes intersected significant intervals of mineralization.
Highlights and analytical results for the geotechnical drilling program are summarized below.
- Four of the six geotechnical drillholes were completed along the east side of the Paramount zone referred
to as the ‘highwall” and two drillholes were completed on the west side of the Paramount zone.
- The mineralization intersected in DDH SCK-24-472 extended the mineralization in the Paramount zone
approximately 250 meters (m) to the north.
- Analytical highlights include:
o DDH SCK-24-471, intersected a core interval of 134.60m (21.60 to 156.20m) that averaged
0.338% copper, 0.0 37% molybdenum, 0.058 g/t gold and 0. 78 g/t silver that included a 63.80m
core interval (59.20 to 123.00 m) that averaged 0. 437% copper, 0.0 66% molybdenum, 0 .050 g/t
gold and 1.11 g/t silver.
o DDH SCK-24-472, intersected a core interval of 208.64m (406.10 to 614.74m) that averaged
0.253% copper, 0.014% molybdenum, 0.115 g/t gold and 0.88 g/t silver.
o DDH SCK-24-476, intersected a core interval of 202.60m (189.70 to 392. 30m) that averaged
0.324% copper, 0.0 23% molybdenum, 0. 044 g/t gold and 1.68 g/t silver that included a 14.40m
core interval (196.80 to 211.20m) that averaged 0. 634% copper, 0.104% molybdenum, 0.092 g/t
gold and 3.48 g/t silver.
- The other three geotechnical drillholes were not expected to intersect mineralization due to their locations
and returned background metal concentrations.
Elmer B. Stewart, President and CEO of Copper Fox, stated, “While the primary purpose of the geotechnical drilling
program was to augment the geotechnical information for the Schaft Creek deposit, the 2024 drilling expanded the
mineralized envelope of the Schaft Creek deposit to the northwest and intersected significant intervals of “near
surface” higher -grade copper-molybdenum mi neralization that provides additional information on the
distribution/continuity of the mineralization within the Paramount zone.”
Analytical Results
The mineralized intervals reported in this news release were calculated using a 0.10% copper equivalent (CuEq)
cut-off grade. Samples lower than the 0.10% CuEq cut-off were included in the weighted average interval provided
that the sample interval below the cut-off did not exceed 10.0m in core length. Intervals of core lost with zero metal
2
concentrations are included in the interval and weighted average metal grades and CuEq estimation. The weighted
average grades of the mineralized intervals are set out in Table-1:
Table 1: Weighted average grades of mineralized intervals from the 2024 geotechnical drilling program.
DDH ID
From
(m)
To
(m)
Interval
(m)
Cu
(%)
Mo
(%)
Au
(g/t)
Ag
(g/t)
CuEq
(%)
SK-24-471 21.60 156.20 134.60 0.338 0.037 0.058 0.78 0.497
including 59.20 123.00 63.80 0.437 0.066 0.050 1.11 0.694
196.65 243.20 46.55 0.125 0.004 0.043 0.39 0.162
330.50 344.85 14.35 0.193 tr. tr. 0.36 0.206
354.90 377.32 22.42 0.096 tr. tr. 0.22 0.108
SK-24-472 94.00 105.60 11.60 0.342 0.024 0.180 2.36 0.521
139.20 163.60 24.40 0.164 tr. 0.284 1.59 0.320
179.20 216.30 37.10 0.064 0.004 0.078 0.58 0.118
284.13 313.50 29.37 0.041 0.005 0.124 0.58 0.121
351.50 391.98 40.48 0.125 0.014 0.084 0.54 0.216
406.10 614.74 208.64 0.253 0.014 0.115 0.88 0.361
including 442.50 507.98 65.48 0.428 0.020 0.221 1.61 0.614
SK-24-476 24.50 169.13 144.63 0.344 0.012 0.041 1.27 0.409
including 24.50 81.50 57.00 0.487 0.012 0.052 1.28 0.560
including 91.50 110.05 18.55 0.492 0.013 0.045 2.34 0.567
189.70 392.30 202.60 0.324 0.023 0.044 1.68 0.433
including 196.80 211.20 14.40 0.634 0.104 0.092 3.48 1.051
including 264.00 294.10 30.10 0.432 0.040 0.051 2.91 0.606
including 354.85 371.50 16.65 0.602 0.030 0.041 1.55 0.752
402.00 426.00 24.00 0.137 0.002 tr. 0.59 0.153
Notes: The mineralized intervals listed in the above table are down hole drill core intervals. Drilling data is insufficient to determine the
true width of the mineralized zone. CuEq = copper equivalent, % = percent, g/t = grams per tonne, m = meter, tr. = trace. Copper equivalent
grades are for comparative purposes onl y and based on calculating the CuEq on an individual sample basis using 100.0% of the copper
content plus 71% of the gold content, 60.1% of the molybdenum content and 40.3% of the silver content . Metal prices used in the copper
equivalent calculation are copper US$ 4.00/lb, gold US$1,900/oz, molybdenum US$23.00/lb and silver US$26.00/oz. Mo concertation less
than 0.003% and gold concentration less than 0.020 g/t are listed as trace. The CuEq (%) are based on the weighted average of the individual
CuEq for each sample over the interval of interest.
Drill collar information and locations of the 2024 geotechnical drillholes is set out in Table 2 and Figure 1 below.
Table 2: Drill collar information for the 2024 geotechnical drilling program.
DDH ID Easting Northing Elevation Azimuth Dip
Total Depth
(m)
SK-24-471 379478 6360338 903.50 290 -65 380.00
SK-24-472 379538 6361053 1165.70 290 -65 624.00
SK-24-473 379986 6360575 1089.40 90 -75 377.00
SK-24-474 380719 6360710 1423.60 220 -65 194.50
SK-24-475 380532 6361102 1569.70 330 -70 381.50
SK-24-476 379481 6360334 903.50 200 -64 516.50
3
The drillhole locations and hole traces of the 2024 geotechnical drilling program are shown in Figure-1:
Figure 1: Plan map of the Schaft Creek deposit showing locations of the 202 4 drillholes, the Five-Year pit shell and Life-of-Mine pit shell
as set out in the “Schaft Creek Preliminary Economic Assessment, an NI 43-101 Technical Report”, with an effective date of September 10,
2021, prepared by Tetra Tech Canada Inc., H. Ghaffari, M.Sc., P.Eng, et al as Qualified Persons.
4
Discussion of Mineralized Drillhole Results
DDH SCK-24-471 was drilled to the northwest and is located on the western side of the Paramount zone . The
higher-grade copper-molybdenum mineralization (core interval from 21.60 to 156.20m) starts at the
overburden/bedrock contact. Three additional intervals of low-grade mineralization were intersected at depth.
DDH SCK-24-472 located at the north end of the Paramount zone was drilled to the west. Due to intensely broken
ground conditions, core recovery started at a downhole depth of 94.0m. In the core interval 94.0 0-391.98m five
intervals ranging from 11.60m to 40.48m of copper-gold-molybdenum mineralization were intersected. The most
significant interval of copper-gold-molybdenum occurs in the core interval 412.0-614.74m and includes a 65.48m
interval of higher-grade copper-molybdenum-gold mineralization.
DDH SCK-24-476 was drilled to the southwest and intersected two significant intervals of mineralization. The
upper mineralized interval (24.5-169.13m) contains two intervals of higher-grade copper mineralization. The lower
interval (189.70-392.50m) contains three intervals of higher-grade copper-molybdenum mineralization and is
underlain by an interval (402.00-426.00m) of significantly lower-grade copper mineralization.
Diamond Drilling and Sampling Procedures
The geotechnical drilling was completed using PQ and HQ diameter core. Overall core recovery was estimated to
be greater than 90%. After cutting with a diamond saw, one half of the core was collected for sample preparation
and analysis and the other half was retained for future reference. Sample intervals were selected to not cross major
lithological or hydrothermal alteration changes and ranged from 0.76 to 3.00m in length, with most intervals being
an average of 2.0m.
Quality Control
The SCJV follows a rigorous Quality Assurance/Quality Control program. In total, 1,253 samples were submitted
as part of the drill core analysis including 1 ,037 split-core samples, 89 commercial certified reference materials
(CRMs) standards, 38 field blanks, 26 pulp duplicates, 38 field duplicates and 25 crush duplicates. The matrix
material of the CRMs is matched to the Schaft Creek deposit geology. All standards used are certified for 4 -acid
digestion and Au by fire assay. Four standards, one field blank, and three duplicates (crush, field, and pulp) were
inserted to each batch of 100 samples. The insertion rate of the CRMs during 2024 was 7:1.
Analytical data for each standard was reviewed on a batch -by-batch basis. Only the performance of Au (by Au -
ICP21), Cu, Mo, and Ag (ME -MS61) were considered in the failure criteria. The performance of non -economic
elements As, Fe, Mg (ME-MS61), Total S by IR08, and Total Cu by sequential leach (Cu-PKG06LI) were used to
monitor digestion and method specific failures. ALS Limited (ALS) located in North Vancouver, British Columbia
completed the analysis of the samples provided. ALS has a 9001:2008 International Standard Organization rating
for Quality Management Systems. ALS has an ISO/IEC 17025:2017 UKAS (ref 4028) accreditation.
Four drillholes from the 2024 program were analyzed using analytical package; Au-ICP21(30g), ME-MS61(0.75g):
Four acid digestion followed by ICP-MS measurement, ME-IR08: Total C by C-IR07 and total S by S -IR08, Cu-
PKG06LI (Seq. Leach Cu) + S -IR06a). Two drillholes were assayed using the modified method multi -element,
analytical package; Au-ICP21(30g), ME-MS61(0.75g): Four acid digestion followed by ICP-MS measurement,
ME-IR08: Total C by C-IR07 and total S by S-IR08, + S-IR06a).
Qualified Person
Elmer B. Stewart, MSc. P. Geol., President and CEO of Copper Fox, is the Company’s non-independent, nominated
Qualified Person pursuant to National Instrument 43-101, Standards for Disclosure for Mineral Projects, has
reviewed and approved the scientific and technical information disclosed in this news release.
5
About Copper Fox
Copper Fox is a Tier 1 Canadian resource company listed on the TSX Venture Exchange (TSXV:CUU) focused on
copper exploration and development in Canada and the United States. The principal assets of Copper Fox and its
wholly owned Canadian and United State s subsidiaries, being Northern Fox Copper Inc. and Desert Fox Copper
Inc., are the 100% ownerships of the Van Dyke ISCR project, and the Mineral Mountain and Sombrero Butte
porphyry copper exploration projects all located in Arizona, the 25% interest in the Schaft Creek Joint Venture with
Teck Resources Limited on the Schaft Creek copper -gold-molybdenum-silver project and the 100% owned
Eaglehead polymetallic porphyry copper project each located in northwestern British Columbia. For more
information on Cop per Fox’s mineral properties and investments visit the Company’s website at
www.copperfoxmetals.com.
On behalf of the Board of Directors
Elmer B. Stewart
President and Chief Executive Officer
For additional information contact: Fidel Montegu at 1-844-484-2820 or [email protected].
Neither TSX Venture Exchange nor its Regulation Services Provider (as that term is defined in the policies of
the TSX Venture Exchange) accepts responsibility for the adequacy or accuracy of this release.
Cautionary Note Regarding Forward-Looking Information
This news release contains “forward -looking information” within the meaning of the Canadian securities laws.
Forward-looking information is generally identifiable by use of the words “believes,” “may,” “plans,” “will,”
“anticipates,” “intends,” “budgets ,” “could ,” “estimates ,” “expects ,” “forecasts ,” “projects ,” and similar
expressions, and the negative of such expressions. Forward-looking information in this news release includes
statements regarding average grade of mineralized intervals ; CuEq calculati ons: geotechnical drillin g; and
collection of additional geotechnical, hydrogeological, environmental data.
In connection with the forward-looking information contained in this news release, Copper Fox and its subsidiaries
have made numerous assumptions , regarding, among other things: th e geological, metallurgical, engineering,
financial and economic advice that Copp er Fox has received is reliable and is based upon practices and
methodologies which are consistent with industry standards. While Copper Fox considers these assumptions to be
reasonable, these assumptions are inherently subject to significant uncertainties and contingencies.
Additionally, there are known and unknown risk factors which could cause Copper Fox’s actual results,
performance, or achievements to be materially different from any future results, performance or achievements
expressed or implied by the forward -looking information contained herein. Known risk factors include, among
others: the average grade of mineralized intervals may not be correct or significant; the CuEq calculations may not
be accurate; the additional geotechnical, hydrogeological, environmental data may not provide the expected results,
the need to obtain additional financing; uncertainty as to the availability and terms of future financing.
A more complete discussion of the risks and uncertainties facing Copper Fox is disclosed in Copper Fox's
continuous disclosure filings with Canadian securities regulatory authorities at www.sedarplus.ca. All forward-
looking information herein is qualified in its entirety by this cautionary statement, and Copper Fox disclaims any
obligation to revise or update any such forward -looking information or to publicly announce the result of any
revisions to any of the forward -looking information contained herein to reflect future results, events, or
developments, except as required by law.