Cerro de Pasco Resources Advances Metallurgical Test Program; Evaluates Two-Concentrate Flowsheet for Silver-Bearing Pyrite and Base Metals
PRESS RELEASE
Cerro de Pasco Resources Advances Metallurgical Test Program; Evaluates
Two-Concentrate Flowsheet for Silver-Bearing Pyrite and Base Metals
MONTRÉAL, Quebec, Canada, June 9, 2026 (GLOBE NEWSWIRE) — Cerro de Pasco Resources Inc.
(TSXV: CDPR | OTCQX: CDPMF | BVL: CDPR (Lima) | FRA: N8HP) ("CDPR" or the "Company") is pleased to
provide an update on the status of the integrated metallurgical test program advancing the Quiulacocha
Tailings Reprocessing Project in central Peru. The results obtained to date, across multiple laboratories and
over 110 individual tests, support a directional path toward a two-concentrate flowsheet, each concentrate
carrying silver, and show strong metallurgical responsiveness of the Phase 1 Quiulacocha tailings samples
to conventional and emerging flotation technologies.
Highlights:
• Conceptual flowsheet with Two Concentrate Streams: Metallurgical testing in bench-scale and
mini-pilot programs has converged on a conceptual flowsheet generating a high-grade pyrite
concentrate and a base metal concentrate, both containing silver (see Figure 1 below).
• Pyrite concentrate stream under evaluation: With pyrite representing more than 50% of the
Quiulacocha tailings portion drilled in 2024, the Company is investigating a pyrite concentrate
stream as an alternative source of sulphur for essential industries such as phosphate-based
fertilizers and chemical reagents used in critical-metal processing.
• Strong silver and sulphide recovery at bench-scale and mini-pilot testing: In the mini-pilot plant
to date, greater than 92.5% of total sulphides and approximately 94% of silver (lattice-bound and
discrete) were recovered into a bulk concentrate, together with the associated base-metal
sulphides.
• Low sulphide tailings:Importantly, the final tails are targeted to contain low residual sulphur, which
test results indicate may reduce acid-generation potential — a key objective of the Company's
remediation strategy, subject to further test work.
• Further optimization work underway: Bench and pilot-scale programs will continue to refine the
flowsheet to produce indicative concentrate specifications to form the basis for subsequent
technical studies and for initial discussions with potential strategic offtake and investment partners.
• Gallium and Indium: Mineralogical studies highlight opportunities to concentrate gallium and
indium. This is leading to targeted exploratory metallurgical test-work focused on the silicate fraction
of the tails to investigate gallium recovery, and on the base metals and pyrite concentrate to
determine indium recovery. This test-work is at early, exploratory stage and any potential is
conceptual.
Steven Zadka, Executive Chairman, commented: "This program has moved us from promising bench-
scale results to a continuous mini-pilot test — an important step in evaluating a project of this scale. The
results to date show strong recovery of silver and sulphides into a single bulk sulphide concentrate, as first
step in the conceptual flowsheet. Critically, a high portion of the silver is recovered with the sulphides rather
than lost to tails, and our program is designed to investigate silver recovery through downstream processing
of the pyrite concentrate — not only to rely on its payability in a pyrite product. The pyrite dominance of these
tailings is the reason we are pursuing a two-concentrate flowsheet: the pyrite stream has potential value as
a sulphur-bearing feedstock in a market where conventional supply is tightening. Significant work remains
— separation into a cleaner pyrite concentrate, roasting and calcine studies, and offtake discussions— but
this material must ultimately be addressed, and we intend to be the ones to address it."
Conceptual Metallurgical Flowsheet
The conceptual flowsheet under development is built around a sequential flotation route designed to
optimize total sulphide recovery while producing two concentrates under evaluation. A simplified schematic
is shown below.
Figure 1: Overview of Tailings Reprocessing Flowsheet Concept
The re-mined tailings, following any required classification and/or regrinding, are first directed to a bulk
sulphide rougher flotation stage operating at acidic pH (typically 4.5–5.5). This approach leverages the
natural floatability of pyrite under acidic conditions, without lime suppression, and concurrently recovers
the associated base metal sulphides and silver-bearing minerals into a high-grade bulk sulphide
concentrate. Non-sulphide gangue (predominantly quartz and manganese-rich siderite) reports to the final
tails, which can be returned to a controlled tailings storage facility.
The bulk sulphide concentrate is then directed to a base metal flotation stage where the contained
sphalerite, galena, copper sulphides and some of the silver-bearing minerals are separated from the pyrite.
This produces:
• A base metal concentrate (potentially as one or two streams), carrying zinc, lead, copper, silver.
• A pyrite concentrate at grading 90–95% pyrite, targeting a combined low zinc-plus-lead content,
potentially suitable for sulphuric-acid production (via roasting), precious-metal recovery, and
emerging sulphur-supply applications.
The flowsheet is conceptual and remains under active optimization. This program is being evaluated using
conventional mechanical cells, as well as specialized fine-grain flotation cells, in order to identify the
optimal combination of recovery, grade and capital efficiency.
Quiulacocha Mineralogy Overview
An in-depth mineralogical characterization program, incorporating quantitative TIMA (TESCAN Integrated
Mineralogical Analysis) and Zeiss-Mineralogic automated mineralogy, electron microprobe, sequential
extraction, hydroseparation and laser-ablation ICP-MS, has been completed on multiple tailings samples
collected during the 2024 drilling program (Phase 1), as well as on concentrate products. The mineralogy is
materially driving flowsheet selection.
Key Mineralogical Observations
Pyrite-dominant feed: The portion of the Quiulacocha tailings drilled in 2024 is mineralogically dominated
by pyrite, which represents in excess of 50% of the bulk material (Figure 2). This is notably high relative to
typical polymetallic tailings and is the principal driver of the two-concentrate-stream approach. Pyrite
liberation is generally good (typically 65–89%, and over 90% in pyrite concentrate samples; Table 1).
Figure 2: Modal mineralogical composition from two composites from the Quiulacocha Tailings generated from Phase 1 drill
cores. Mineral Liberation Analysis performed by Erzlabor, in Freiberg (Germany), through measurement mode GXMAP (Grain
X-ray Mapping) in July 2025
Table 1: Liberation analysis for pyrite in feed, bulk sulphide concentrate and tails. Mini-Pilot Plant Test MG#6 (completed 13
March 2026). SGS Mineralogy Report, Phase 1, SGS-Santiago.
Mineral / Mass [wt%] Feed MG#6 Conc Final MG#6 Tailings Final MG#6
Free (95% area) 78.73 80.86 56.28
Lib (80% area & 50% perimeter) 11.09 10.95 13.87
Mid (50% area & 20% perimeter) 5.73 5.35 12.16
Sub Mid (20% area & 10% perimeter) 3.13 2.47 6.65
Locked 1.32 0.37 11.04
Total 100.00 100.00 100.00
Silver association with sulphides: Silver occurs as lattice-bound silver within sulphides (based on
microprobe analysis, Universidad de Barcelona, Spain) and as discrete minerals (argentite/acanthite (Ag₂S)
and matildite (AgBiS₂)), intimately associated with pyrite, mainly as inclusions (Zeiss-Mineralogic, Luleå
University of Technology, Sweden). Consequently, a high proportion of silver reports to the bulk sulphide
concentrate and would subsequently distribute to pyrite and base-metal concentrate streams.
Together, these mineralogical findings explain why the bulk-sulphide-first flowsheet under investigation
delivers more consistent results: it captures the silver and base metals that are mineralogically locked with
pyrite, before applying selective separation chemistry to a lower-mass concentrate stream.
Table 2: Modal composition for feed, bulk sulphide concentrate and tails associated with Mini-Pilot Plant Test MG#6. SGS
Mineralogy report, Phase 1
Sulphides and gangue minerals Feed MG#6 Con MG#6 Tails MG#6
Copper sulphides 0.02 0.05 0.00
Sphalerite 1.95 1.83 0.94
Galena 0.35 0.43 0.23
Pyrite 54.24 89.74 3.81
Pyrrhotite 0.40 0.26 0.01
Arsenopyrite 0.19 0.25 0.04
Quartz 15.61 2.50 37.29
Other silicates 0.08 0.27 1.72
Fe Oxides/Hydroxides 0.34 0.02 0.52
Carbonates (Mostly siderite) 25.05 3.23 53.97
Sulphates & Phosphates 1.02 1.38 1.44
Others 0.01 0.02 0.01
Total 100.00 100.00 100.00
Gallium and Indium: Geochemical (Sequential leaching) and mineralogical studies (TIMA; LA-ICPMS, SEM)
show gallium is deporting to the crystalline lattice of gangue minerals like kaolinite and Aluminium-
Phosphate-Sulphate (APS) mineral phases. These minerals, preferentially reporting to tailings after bulk
sulphide concentration, represent an opportunity for reverse or selective concentration to increase overall
gallium content. In addition, indium is primarily associated with sphalerite, the main zinc-bearing mineral,
and therefore reports to the base metals stream. Exploratory work for gallium and indium concentration is
being studied through bench-scale tests and currently waiting for first results. Metallurgical parameters
defined after best bench-scale result will eventually be used in dedicated mini pilot plant runs.
Laboratory Bench-scale Tests
The mini-pilot plant campaign at SGS Santiago builds on, and corroborates at continuous scale, a structured
bench-scale test program comprising more than 110 individual flotation tests conducted across multiple
internationally recognized laboratories — including Maelgwyn (United Kingdom), Plenge (Peru), XPS
(Canada) and SGS (Chile). The program was organised into two complementary workstreams: 65 sequential
flotation tests evaluating the staged recovery of copper-lead, zinc and pyrite into separate concentrates;
and 45 pyrite-focused flotation tests assessed under three distinct scenarios (selective precious-metal
recovery, bulk sulphide concentrate, and sulphur-optimized pyrite concentrate).
The 12 selected bench-scale rougher tests, together with MG#6 mini-pilot result in Table 3 and Figure 3
indicate that, on the samples tested, a single bulk-sulphide flotation stage recovers a large proportion of
silver (87–95%) and pyrite (93–99%) into a concentrate, together with a significant proportion of the zinc (62–
82%) and lead (60–78%). These recoveries reflect a bulk-sulphide pull of approximately 67% of feed mass,
consistent with the sulphide-dominant nature of the tailings; the bulk concentrate is an intermediate step,
subsequently separated into pyrite and base-metal concentrates.
The first mini-pilot campaign at SGS Santiago (test MG#6) returned recoveries that fall within the bench-
scale range on every metal reported - silver, zinc, lead and sulphur - providing an initial indication of scaled-
up reproducibility.
The results presented in the table and chart are exploratory in nature, relate only to the specific samples and
conditions tested, and have not been demonstrated at commercial scale. Further test work, completion of
the Phase 2 drilling and resource-definition programs, metallurgical testing on Phase 2 samples, and
additional engineering studies are required before any conclusions can be drawn about the deposit as a
whole or about the characteristics of any contemplated product stream.
Table 3: Summary of bench scale and mini-pilot results relevant to the bulk-sulphide flotation (prior to base metal flotation).
These results do not represent the final targeted pyrite concentrate
Test Head grade
Test ID Composite Lab Type Ag (g/t) Au (g/t) Cu (%) Pb (%) Zn (%) As (%) Fe (%) S (%)
FT-5 25-0009-GM Plenge Bench 55.62 0.14 0.14 1.14 1.43 0.30 34.69 33.96
F007 25-0009-GM XPS Bench 52.65 n.r. 0.12 0.88 1.48 0.25 31.45 29.51
KF-5 25-0005-GM Plenge Bench 47.83 n.r. 0.09 0.95 1.54 n.r. 30.93 27.97
FT-1 25-0009-GM Plenge Bench 45.77 0.15 0.11 0.87 1.51 0.25 29.67 29.85
FT-39 26-0001-BK Plenge Bench 45.42 0.04 0.03 0.49 1.17 0.19 32.11 30.29
FT-41 26-0001-BK Plenge Bench 45.45 0.04 0.03 0.47 1.25 0.19 32.64 29.66
FT-37 26-0001-BK Plenge Bench 46.39 0.04 0.03 0.50 1.22 0.19 31.91 29.89
FT-2 25-0009-GM Plenge Bench 45.76 0.14 0.11 0.82 1.49 0.23 29.39 29.71
FT-7 25-0009-GM Plenge Bench 45.93 0.13 0.12 0.87 1.53 0.24 29.57 29.47
FT-40 26-0001-BK Plenge Bench 45.22 0.04 0.03 0.51 1.19 0.18 32.26 28.85
FT-42 26-0001-BK Plenge Bench 44.65 0.04 0.04 0.50 1.20 0.19 32.16 29.29
FT-4 25-0009-GM Plenge Bench 37.40 0.17 0.09 0.37 1.65 0.17 26.94 27.64
MG#6 26-0001-BK SGS Chile Mini-pilot 49.20 n.r. 0.03 0.52 1.13 n.r. 34.10 28.70
Test Mass Recovery (%) Conc. grade
Test
ID Composite Type
Mass
Rec
(%)
Ag Au Cu Pb Zn As Fe S Ag
(g/t)
Au
(g/t)
Cu
(%)
Pb
(%)
Zn
(%)
As
(%)
Fe
(%) S (%)
FT-5 25-0009-GM Bench 68.5 88.5 88.4 84.6 68.8 80.7 87.6 84.8 97.8 71.79 0.18 0.17 1.14 1.69 0.38 42.95 48.44
F007 25-0009-GM Bench 62.6 89.3 n.r. 83.4 65.9 82.3 86.5 82.6 97.0 75.16 n.r. 0.15 0.92 1.94 0.35 41.53 45.76
KF-5 25-0005-GM Bench 60.8 92.8 n.r. 92.6 78.0 75.2 n.r. 81.4 97.2 72.98 n.r. 0.14 1.22 1.90 n.r. 41.39 44.73
FT-1 25-0009-GM Bench 57.2 87.4 88.0 83.2 63.0 81.3 85.6 78.9 95.9 69.99 0.22 0.17 0.96 2.15 0.38 40.94 50.07
FT-39 26-0001-BK Bench 61.0 93.6 84.1 79.0 74.5 71.6 90.8 74.6 97.7 69.68 0.05 0.04 0.60 1.38 0.29 39.28 48.52
FT-41 26-0001-BK Bench 62.0 94.6 84.4 78.6 76.1 74.8 90.6 74.9 98.6 69.41 0.05 0.04 0.58 1.51 0.28 39.45 47.18
FT-37 26-0001-BK Bench 60.6 92.0 83.3 80.6 70.0 62.9 89.0 74.8 97.1 70.42 0.06 0.04 0.58 1.27 0.28 39.41 47.93
FT-2 25-0009-GM Bench 58.9 87.2 89.2 81.9 63.6 78.0 85.9 81.0 97.3 67.75 0.22 0.15 0.89 1.97 0.34 40.42 49.08
FT-7 25-0009-GM Bench 59.2 89.5 86.0 78.1 60.7 77.9 81.3 76.4 93.0 69.43 0.20 0.16 0.95 2.16 0.35 40.88 49.60
FT-40 26-0001-BK Bench 56.5 89.6 79.5 74.8 66.0 72.0 85.4 71.2 96.0 71.69 0.05 0.05 0.59 1.51 0.28 40.64 48.97
FT-42 26-0001-BK Bench 56.9 90.0 80.6 72.0 67.0 72.7 84.3 71.8 95.8 70.68 0.05 0.04 0.59 1.53 0.28 40.57 49.34
FT-4 25-0009-GM Bench 51.7 87.9 82.3 85.5 69.8 82.5 87.3 81.0 95.1 63.58 0.27 0.14 0.50 2.62 0.29 42.18 50.82
MG#6 26-0001-BK Mini-pilot 66.9 94.0 67.0 88.4 73.2 73.8 90.9 80.2 97.5 67.00 <0.2 0.04 0.69 1.26 0.29 43.67 43.98
View full table 3 in PDF
Figure 3: Box plots of recovery range per metal from selected bench-scale test and mini-pilot results.
Mini-Pilot Plant Program
Building on extensive bench-scale work, the Company completed a mini-pilot plant campaign at SGS
Santiago, Chile, using an approximately 12-tonne bulk sample of Quiulacocha tailings collected from a test
pit in December 2025 / January 2026 (see Figure 7. Location map). The mini-pilot plant was operated over
multiple continuous 10–12-hour shifts, with feed, concentrate and tails streams subjected to TIMA
quantitative mineralogy and full geochemical assay (Figure 4).
Headline Mini-Pilot Plant Results
Results below relate to the bulk sample tested and are not representative of the whole tailings.
• Greater than 92.5% of total sulphides recovered into the bulk sulphide concentrate.
• Approximately 73% of zinc reported to the bulk concentrate.
• 94% silver (lattice-bound and discrete) chemically reported to the bulk concentrate.
• Final concentrate is mineralogically more than 90% pyrite (mainly pyrite with traces of pyrrhotite
and arsenopyrite) — a strong base from which to generate either a high-purity pyrite product or to
apply secondary base metal upgrading.
• Greater than 94% of gangue mineralsrejected to the final tails and only approximately 4% residual
pyrite — indicating potential for reduced acid-generation, subject to further test work.
Subsequent stages of the SGS program, currently being run through additional 12-hour shifts, are evaluating
the separation of base metals (zinc, lead, copper and silver) from the bulk sulphide concentrate, and the
conditions required to deliver pyrite concentrate purities of 90–95% with combined low zinc-plus-lead
concentration, typically sought by sulphuric-acid producers, including characterization and management
of minor deleterious elements to meet requirements.
Figure 4: Photos of the Mini-Pilot Plant at SGS Chile with mechanical cells (left) and column cell (centre), and bulk-sulphide
flotation test (right)
Pyrite: A Potential Sulphur Resource for Fertilizer and Industrial Markets
The high pyrite content of the Quiulacocha tailings drilled in 2024, originally regarded as a metallurgical
challenge, has emerged as one of the project's potentially attractive features. Globally, the sulphur market
is undergoing a structural shift. Traditional sources of elemental sulphur, principally a by-product of oil
refining and natural gas processing, have been declining as the hydrocarbon industry transitions, while
demand from the phosphate-fertilizer sector and industrial chemicals continues to grow (Figure 5).
According to commodity market reporting in April 2026, export restrictions on sulphuric acid from China —
the largest producing and exporting jurisdiction — combined with sulphur supply disruptions linked to
conflict in the Middle East, have contributed to elevated sulphuric acid pricing and increased focus on
alternative sulphur-bearing feedstocks.
In this environment, high-quality pyrite concentrate is being evaluated as a potential alternative feedstock.
Pyrite can be roasted to produce sulphur dioxide for sulphuric-acid manufacture, while also generating a
precious-metal-bearing calcine from which silver and other metals may potentially be recovered. The
Company has had initial discussions with multiple parties regarding the potential supply of pyrite
concentrate for sulphuric acid and related industrial applications. These discussions are preliminary and
non-binding, and there is no assurance that they will result in any agreement, sale or revenue.
Figure 5: Sulphuric Acid Demand Growth Forecast by Industry (Mt)
Source: CRU Sulphuric Acid Market Outlook; general industry data, not project-specific
The city of Cerro de Pasco is served by an established rail network (Ferrocarril Central Andino), providing a
path for large-tonnage product transport direct to the coast for ocean freight. The Port of Callao near Lima
is a major deep-water port facility, with significant bulk export capacity.
Further Test Work and Next Steps
The current metallurgical program is comprehensive and multi-laboratory. The Company expects to
complete the following workstreams over the coming months, which will de-risk the conceptual flowsheet
and inform engineering trade-off studies:
• Further optimization work on mini-plant: Separation of base metals from the bulk sulphide
concentrate and generation of cleaned pyrite concentrate samples for downstream evaluation.
• Fine-grain flotation technology evaluation: Comparative bench-scale test work focused on
flowsheet validation, fine-grained sulphide recovery, with results expected to inform a fine-particle
flotation strategy.
• Roasting and leaching test work: Pyrite roasting trials and calcine leaching programs at two
commercial laboratories to test downstream metals recovery from the pyrite concentrate, including
silver and base metals. These programs are designed to investigate the final metal splits between
the two concentrates and the potential payable metal content of each product — the parameters
required for future technical studies and economic evaluations of the Project.
• Gallium: Targeted exploratory metallurgical programs aiming to concentrate gallium through
selective or reverse flotation from the silicate fraction of the tails, and indium associated with the
base metals and pyrite streams. A consolidated metallurgical update is anticipated in the second
half of 2026. This will support advancement toward the Company's first Mineral Resource Estimate
and subsequent technical studies for the Quiulacocha Tailings Reprocessing Project.
0
75
150
225
300
375
450
2000 2005 2010 2015 2020 2025 2030 2035 2040 2045 2050
Fertilizer Metals Industrial