Cantex receives spectacular silver-lead-zinc drill results from the North Rackla claims, Yukon
Cantex receives spectacular silver-lead-zinc
drill results from the North Rackla claims,
Yukon
KELOWNA, BC
,
Oct. 29, 2018
/CNW/ -
Cantex Mine Development Corp.
(CD: TSXV) (the
"Company") is pleased to announce drill results from the Massive Sulphide zone on its 100% owned
14,077 hectare North Rackla claim block.
Discovery Zone Cross Section (CNW Group/Cantex Mine Development Corp.)
Results Received
Results have now been received for nine holes from this summer's diamond drill program. Final
results are available from four holes tested mineralization at the "Discovery Zone" near the
northeastern end of the Massive Sulphide zone. Provisional results are available for five holes at the
"Extension Zone" 1,700 metres to the southwest. These results are provisional as they contain
samples which either
exceed 30% zinc or 20% lead
which is the limit of the analytical method
used. There are 14 drill core samples totaling 12.05 metres containing over 30% zinc and 9 drill
core samples totaling 6 metres containing over 20% lead. These assays are being repeated using
titration methods capable of analysing up to 50% zinc and 70% lead and will be released when
received in about three weeks time.
Discovery Zone Results
Four holes testing the sulphide mineralization at the discovery zone were completed during the
summer drill program. Holes YKDD18-008 and YKDD18-009 were drilled at -63
o
and -44
o
respectively, near the top of the slope and both intersected intensely weathered mineralization. The
third hole, YKDD18-010, was drilled at -50
o
from a second pad 79 metres in elevation below the
upper pad. The fourth hole, YXDD18-011, was drilled at -50
o
. a further 48 metres in elevation down
the mountain. All the holes were drilled at an azimuth of approximately 165 degrees along a single
section, perpendicular to the interpreted strike of the mineralization.
In the following table a summary of the significant intercepts of these four holes is presented.
Hole
From
(m)
To
(m)
Length
1
(m)
Silver
(ppm)
Lead
(%)
Zinc
(%)
YKDD18-008
12.00
13.00
1.00
1.99
0.04
4.05
19.56
20.56
1.00
2.17
0.09
2.52
22.71
24.71
2.00
16.33
3.29
4.74
YKDD18-009
16.32
24.62
8.30
27.05
2.53
3.72
Including
17.32
18.32
1.00
61.60
11.10
7.18
and
20.32
21.32
1.00
47.70
7.53
7.15
and
23.92
24.62
0.70
32.20
1.04
8.58
YKDD18-010
1.15
13.25
12.10
18.75
2.27
7.36
Including
1.15
5.25
4.10
43.49
5.24
14.27
135.65
136.35
0.70
10.80
0.27
2.16
YKDD18-011
111.05
111.85
0.80
72.20
0.34
0.97
1
Note that lengths in the above table are apparent widths and not true widths.
As seen in the above table hole YKDD18-009 intersected
8.30m
of oxidized mineralization with three
higher-grade zones measuring one metre containing up to 61.6 g/t silver, 11.10% lead and 7.18%
zinc.
Hole YKDD18-010 intersected a
12.1m
mineralized zone with a
4.1m
higher-grade zone containing
43.49g/t silver, 5.24% lead and 14.27% zinc.
Extension Zone Results
Drill testing beneath the strongly weathered mineralization encountered in previous drilling (see
release dated
April 7, 2017
) intersected fresh sulphide mineralization. This fresh mineralization not
only has higher grades, but also demonstrates the significant widths of the system at depth.
The five holes were drilled from the same location. Holes YKDD18-012, YKDD18-013 and
YKDD18-014 were all drilled at an azimuth of 137 degrees and at dips of -60, -70 and -80 degrees
respectively. Hole YKDD18-015 was drilled at an azimuth of 102 degrees and a dip of -60
degrees. YKDD18-016 was drilled at an azimuth of 180 degrees and a dip of -60 degrees. These
holes tested the main mineralization along a
56m
strike length and to a depth of
190m
below
surface.
As presented in the table below, each hole contained exceptional intercepts. Every hole contained
samples which exceeded the upper limit of the assay technique of either 20% lead or 30% zinc.
These samples are presently being re-assayed and these results will further improve the provisional
results available now.
Hole
From
(m)
To
(m)
Length
1
(m)
Silver
(ppm)
Lead
(%)
Zinc
(%)
Provisional
YKDD18-012
100.87
113.87
13.00
150.6
7.85*
15.86*
*
Including
102.87
107.87
5.00
277.8
13.39*
29.68*
*
134.74
141.74
7.00
22.0
1.23
8.27
YKDD18-013
77.18
79.28
2.10
14.7
0.98
3.06
121.45
133.82
12.37
158.0
6.04
16.96*
*
Including
123.35
129.00
5.65
207.5
7.43
29.20*
*
155.10
157.12
2.02
19.5
1.02
3.14
YKDD18-014
177.40
179.40
2.00
46.5
0.18
0.49
183.40
205.40
22.00
122.6
6.74*
10.27*
*
Including
184.40
186.40
2.00
158.0
6.93
30.00*
*
and
190.40
192.40
2.00
475.5
18.03*
13.73
*
YKDD18-015
124.28
133.28
9.00
67.2
5.37*
9.87*
*
Including
127.28
128.28
1.00
233.0
9.96
30.00*
*
YKDD18-016
99.77
104.27
4.50
45.6
12.85*
1.74
*
106.27
114.90
8.63
142.1
10.19*
16.66*
*
Including
107.27
109.27
2.00
272.0
17.55*
25.99*
*
and
111.27
112.77
1.50
210.0
14.37
26.47*
*
1
Note that lengths in the above table are apparent widths.
*
Provisional. Results labelled "Provisional" in the above table contain samples which exceeded either 20% lead or 30% zinc. For the purposes of this table these samples are
deemed to have either 20% lead or 30% zinc. Final results for the intervals will be provided when the titration results are received.
As presented in the table above, hole YKDD18-012 contained two mineralized intervals with one
being a
13m
interval of 150.6 g/t silver, 7.85% lead and 15.86% zinc. Within this interval there was
a 5 metre section that contained 277.8 g/t silver, 13.39% lead and 29.68% zinc.
YKDD18-013 intersected three mineralized intervals. The most significant was
12.37m
of 158 g/t
silver, 6.04% lead and 16.96% zinc. Contained within this interval was a 5 metre higher grade
section with 207.5 g/t silver, 7.43% lead and 29.20% zinc.
Hole YKDD18-014 intersected two mineralized intervals including 22 metres of 122.6 g/t silver,
6.74% lead and 10.27% zinc. Within this were two higher grade two metre zones which contained
158.0 g/t silver, 6.93% lead, 30.00% zinc and 475.5 g/t silver, 18.03% lead, 13.73% zinc
respectively.
YKDD18-015 contained a 9 metre interval of 67.2 g/t silver, 5.37% lead and 9.87% zinc.
Hole YKDD18-016 contained two mineralized intervals two metres apart. The most significant was
8.63 metres of 142.1 g/t silver, 10.19% lead and 16.66% zinc.
A cross section through holes YKDD18-012, YKDD18-013 and YKDD-014 is attached to this
release. It also shows the results from three holes completed in late 2016 which intersected highly
weathered mineralization near surface. Additional maps and sections are presented on the
Company's website
www.cantex.ca
.
Deposit Style
Cantex has traced the mineralized zone for approximately three kilometres. The strata bound
mineralization is contained within Proterozoic age marine clastic rocks and contains elevated silver,
lead, zinc and manganese. These are geological characteristics similar to other globally significant
massive sulphide mines such as the Sullivan Mine in
British Columbia
, and the Mount Isa & Broken
Hill Mines in
Australia
.
Quality Controls / Qualified Person
The drill holes reported in this press release were drilled using HQ (63.5mm) diamond drill bits. The
core was logged, marked up for sampling and then divided into equal halves using a diamond saw on
site. One half of the core was left in the original core box and these boxes were removed from site
and is stored in a secure facility. The other half was sampled and placed into sealed bags which
were in turn placed into larger bags closed with security seals prior to being transported by
commercial carrier to CF Mineral Research Ltd in
Kelowna, BC
.
At CF Minerals the samples were dried prior to crushing to -10 mesh. The samples, which averaged
over 3kg, were then mixed prior to splitting off 800g. The 800g splits were pulverized to -200 mesh
and a 250g split was sent for assay. Quality control procedures included the insertion of coarse
quartz samples to assess the sample preparation. Silica blanks were inserted along with certified
reference samples. These quality control samples were each inserted approximately every 20
samples.
ALS Chemex in
Vancouver
assayed the samples using a four acid digestion with an ICP-MS finish.
The 48 element ME-MS61 technique was used to provide a geochemical signature of the
mineralization. Where lead or zinc values exceeded one percent the Pb-OG62 or Zn-OG62
techniques were used. These have upper limits of 20% lead and 30% zinc respectively. Over limit
samples are presently being analyzed by titration methods Zn-VOL50 and Pb-VOL70.
The technical information and results reported here have been reviewed by Mr.
Chad Ulansky
P.Geol
., a Qualified Person under National Instrument 43-101, who is responsible for the technical
content of this release.
Signed,
Charles Fipke
Charles Fipke
Chairman
Neither TSX Venture Exchange nor its Regulation Services Provider (as that term is defined in the
policies of the TSX Venture Exchange) accepts responsibility for the adequacy or accuracy of this
release. Information set forth in this news release includes forward-looking statements under
applicable securities laws. Forward-looking statements are statements that relate to future, not
past, events. In this context, forward-looking statements often address expected future business
and financial performance, and often contain words such as "anticipate", "believe", "plan",
"estimate", "expect", and "intend", statements that an action or event "may", "might", "could",
"should", or "will" be taken or occur, or other similar expressions. All statements, other than
statements of historical fact, included herein including, without limitation; statements about the
terms and completion of the proposed sale transaction are forward-looking statements. By their
nature, forward-looking statements involve known and unknown risks, uncertainties and other
factors which may cause the actual results, performance or achievements, or other future events,
to be materially different from any future results, performance or achievements expressed or
implied by such forward-looking statements. Such factors include, among others, risks identified in
the management discussion and analysis section of the Company's interim and most recent annual
financial statement or other reports and filings with Canadian securities regulators. Forward
looking statements are made based on management's beliefs, estimates and opinions on the date
that statements are made and the respective companies undertakes no obligation to update
forward-looking statements if these beliefs, estimates and opinions or other circumstances should
change, except as required by applicable securities laws. Investors are cautioned against
attributing undue certainty to forward-looking statements.
SOURCE
Cantex Mine Development Corp.
View original content to download multimedia:
http://www.newswire.ca/en/releases/archive/October2018/29/c8007.html
%SEDAR: 00010333E
For further information:
Cantex Mine Development Corp, Tel: +250-860-8582; Email:
CO: Cantex Mine Development Corp.
CNW 09:00e 29-OCT-18