Cabral Gold Inc. (TSXV: CBR) (OTC Pink: CBGZF) ("Cabral" or the "Company") commenced its inaugural diamond drill program this January, and is very pleased to announce the discovery of a new high-grade gold system following the initial six reconnaissance diamond drill holes at the Machichie target
Cabral cuts 3.4m @ 36.9 g/t gold in Machichie Drilling
and Announces the Discovery of a New High-grade Zone
at the Cuiú Cuiú Project, Brazil
Vancouver, British Columbia--(Newsfile Corp. - February 28, 2019) -
Cabral Gold Inc. (TSXV:
CBR) (OTC Pink: CBGZF)
("Cabral" or the "Company")
commenced its inaugural diamond drill program this January, and
is very pleased to announce
the discovery of a new high-grade gold system following the initial six reconnaissance diamond drill holes at the Machichie target
at the Cuiú Cuiú Project, Pará State, northern Brazil. The Machichie target has never been previously drill tested. This Machichie
Phase I reconnaissance diamond-drill program is part of a larger 20-hole reconnaissance program designed to test nine
separate high-grade gold targets.
Highlights
Drill hole CC182-19 targeted a NE-trending structure, coincident with a NE-trending magnetic low, and returned
3.4m @
36.9 g/t gold
including
0.7m @ 162.7 g/t gold
. The structure remains open along strike and at depth
Drill hole CC178-19 returned
2.1m @ 15.3 g/t gold
within the main E-W trending Machichie magnetic low target which is
also previously undrilled. A shallower hole CC177-19 drilled along the same section returned
3.1m @ 7.3 g/t gold
including 0.6m @ 24.7 g/t gold.
These results confirm vertical continuity of high-grade mineralization from surface to
80m. The zone remains open at depth and along strike
Drill hole CC179-19 tested the main E-W target and returned
0.5m @ 20.2 g/t gold
and was drilled 175m west of CC177-
19 and CC178-19
Drill hole CC181-19 tested the main E-W target, 275m west of CC177-19 and returned
0.6m @ 10.0 g/t gold
.
Wider zones of lower grade mineralization are associated with and enclose the high-grade E-W trending intervals
Machichie Drill Results
The Machichie target is located just 500m north of the MG deposit. MG is currently the second largest gold deposit known at
Cuiú Cuiú, with an Inferred Resource of 8.6MMt @ 1.45 g/t gold (0.4MMoz of gold)
[1]
.
Machichie was selected as a priority target for drill testing following the identification of high-grade gold mineralization from
shallow artisanal shafts in mid-2018 (see press release dated July 19, 2018). A composite grab sample returned 336 g/t Au
from a 1m wide quartz-pyrite vein in the principal shaft in the area.
Results from channel sampling in subsidiary shafts and
galleries in weathered bedrock along strike included 0.80m @ 54.6 g/t Au, 1.5m @ 13.8 g/t Au, 0.75m @ 13.2 g/t gold and
1.75m @ 5.8 g/t gold. A recent grab sample from stockpiles of the principal shaft returned
356 g/t Au, 198 g/t Ag, 1% Cu and
0.1% Mo
(see press release dated January 29, 2019).
The high-grade surface mineralization and workings at Machichie extend over at least 750m in strike length and are coincident
with a strong E-W trending magnetic anomaly, resembling that of
the MG deposit (Figures 1 and 2). The structure is considered
to extend further under soil cover to the east and west. Diamond drill and assay results from the initial six holes are summarized
below in Table 1. Further drill hole details are provided in Table 2.
Drill hole
From (m)
To (m)
Interval (m)
Grade (g/t gold)
CC177-19
23.4
25.5
2.1
0.9
+
37.5
82.5
45.0
1.0
incl.
37.9
38.1
0.2
23.9
+ incl.
44.5
44.9
0.4
13.4
+ incl.
53.7
54.0
0.3
11.4
+ incl.
61.4
64.5
3.1
7.3
Inc.
63.6
64.2
0.6
24.7
CC178-19
31.6
94.4
62.8
0.9
incl.
91.7
93.8
2.1
15.3
+
112.2
115.9
3.7
0.9
CC179-19
33.9
50.2
16.3
1.3
incl.
39.1
39.6
0.5
20.2
CC180-19
Hole lost at 40.5m in saprolite. Results pending
CC181-19
38.4
45.0
6.6
1.6
incl.
38.4
39.0
0.6
10.0
CC182-19
32.2
35.6
3.4
36.9
incl.
33.9
34.6
0.7
162.7
Table 1: Drill results from the Machichie target
Machichie Main East-West Trend
Five holes tested the main E-W trending Machiche magnetic-low trend.
With the exception of one hole, which terminated early
due to drilling difficulties, all holes encountered high-grade quartz-sulphide veins and/or silica-sulphide-rich zones. In places,
these are encompassed by broader lower grade alteration envelopes. The recognition of the lower grade mineralized envelope
was unexpected at Machichie. however, the signature is similar to that observed at the MG deposit 500m to the south.
MG is
characterized by multiple higher-grade zones within a broader alteration envelope.
Figure 1: Map showing location of magnetic lows and recent drilling at Machichie in relation to MG deposit
To view an enhanced version of Figure 1, please visit:
https://orders.newsfilecorp.com/files/3900/43114_ddf710f774f85b89_002full.jpg
The first two diamond drill holes, CC177-19 and CC178-19 were completed on section 553005E. These combined to establish
vertical continuity beneath high-grade mineralization that was previously recognised and sampled at surface (Figures 1, 2 and
3).
Drill Hole CC177-19 cut
3.1m @ 7.3 g/t gold
within a broader mineralized envelope that returned
45m @ 1.0 g/t gold
. Several
other narrow high-grade veins are evident within this broader envelope including
0.2m @ 23.9 g/t, 0.4m @ 13.4 g/t and 0.6m
@ 24.7 g/t gold
.
Drill hole CC-178-19 was drilled from the same platform immediately below CC-177-19 and similarly cut the same structure,
returning
2.1m @ 15.3 g/t gold
, approximately 30m below the intercept in CC177-19, or 80m below surface. The high-grade
zone is similarly enclosed within a broader lower grade envelope of
62.8m @ 0.9 g/t gold
(Figures 2 and 3).
Drill hole CC179-19 was a step out hole that was drilled approximately 175m west of CC177-19 and CC178-19 and intersected
the same mineralized structure and returned
0.5m @ 20.2
g/t gold within a lower grade envelope of
16.3m @ 1.3 g/t gold
.
Drill holes CC180-19 and CC181-19 were drilled 275m further west of CC177-19. Hole CC180-19 was lost at 40.5m in
saprolite before reaching the target zone and results are pending from this hole, but hole CC181-19 again intersected what is
interpreted as the extension of the same high-grade structure returning
0.6m @ 10.0 g/t gold
within a narrower lower grade
interval of
6.6m @ 1.6 g/t gold
.
Figure 2: Map showing location of Machichie drill holes in relation to MG deposit
To view an enhanced version of Figure 2, please visit:
https://orders.newsfilecorp.com/files/3900/43114_ddf710f774f85b89_003full.jpg
Figure 3: Schematic cross section of line 553005E at Machichie showing drill holes CC177-19 and CC178-19
To view an enhanced version of Figure 3, please visit:
https://orders.newsfilecorp.com/files/3900/43114_ddf710f774f85b89_004full.jpg
These initial reconnaissance drill holes clearly demonstrate the presence of an E-W trending zone of high-grade gold
mineralization at Machichie which is surrounded by a broader lower grade envelope.
Drilling at the Machichie main E-W trend in this Phase I reconnaissance program has been constrained to a 275m segment of a
much larger magnetic-low E-W trend, and was focussed along the northern contact, where overburden depths are shallower and
artisanal workers have exposed basement gold mineralization. Much of the width of the magnetic-low trend remains untested
and gold mineralized remains open beyond the 275m of strike length and at depth.
Machichie Northeast Trend
Drill hole CC182-19 (Figures 1, 2 and 4) was drilled 280m SW of hole CC181-19 beneath another previously untested NE-
trending structure which returned values of 19.2 g/t gold from surface rock chip sampling. This structure is also coincident with
another significant magnetic low trend. The hole intersected a pronounced interval of quartz-sulphide alteration and veining at
32m depth, which returned
3.4m @ 36.9 g/t gold including 0.7m @ 162.7 g/t gold
(Figure 4). The zone is open at depth and
undrilled along strike in both directions. This NE structural trend, and coincident magnetic low, converges towards the main E-W
trending Machichie structure (Figures 1 and 2).
Mineralization remains open along strike and at depth.
Figure 4: Quartz-sulphide vein structure intersected in hole CC182-19 which returned 3.4m @ 36.9 g/t gold
Cannot view Figure 4? Visit:
https://orders.newsfilecorp.com/files/3900/43114_veinstructure.jpg
Machichie East Target
Reconnaissance hole CC183-19 was recently completed to a depth of 250.5m at the Machichie East target (see press release
dated January 29, 2019). This hole was collared on Section 553680E, approximately 400m NE of CC177-19.
It was designed to
test a coincident magnetic low (Figure 1), IP chargeability anomaly, and multi-element saprolite/soil geochemical anomaly.
CC183-19 intersected intervals of strong silica-pyrite alteration and at least three previously unknown quartz-pyrite vein zones.
Extensive scheelite and minor molybdenite was observed in veins and disseminations in the host rock. Assay results are
pending.
Next Steps
Drilling is currently proceeding at the MG deposit which contains an existing low grade and E-W trending Inferred Resource of
8.6MMt @ 1.45 g/t Au (0.4MMoz of gold). A re-interpretation of the historic drill data suggests that the low-grade resource may
be cut by previously unrecognised NE-trending narrow high-grade zones. Three holes are planned to test for potential high-grade
structures at MG.
Following completion of drilling at MG, Cabral intends to complete reconnaissance drilling at five additional high-grade targets.
Once the Phase I reconnaissance program is complete the Company expects to systematically follow-up the highest priority drill-
core assay results with a view to expanding and upgrading the current resource base at Cuiú Cuiú.
Alan Carter, President and CEO stated "these initial drill results from the previously untested Machichie target strongly support
our belief that numerous high-grade zones of gold mineralization exist at the Cuiú Cuiú project. Clearly, we have made a new
discovery which has the potential to grow to be a significant high-grade deposit. I would like to extend my congratulations and
thanks to our exploration team in Brazil and hope that these initial drill results will dispel the myth that gold mineralization at Cuiú
Cuiú is only low grade".
Hole
X
Y
Dip/Az
Saprolite depth (m)
EOH (m)
CC_177_19
553007
9343478
-50/000
19.1
87.3
CC_178_19
553007
9343478
-62/000
25.3
121.3
CC_179_19
552835
9343504
-50/000
0.3
98.5
CC_180_19
552733
9343584
-50/180
30.3
40.5
CC_181_19
552733
9343584
-60/180
37.5
149.6
CC_182_19
552555
9343364
-50/315
21.0
65.5
TOTAL
562.7
Table 2: Location information and saprolite depths for Machichie drill holes
About Cabral Gold Inc.
The Company is a junior resource company engaged in the identification, exploration and development of mineral properties,
with a primary focus on gold properties located in Brazil.
The Company owns the Cuiú Cuiú gold project, which covers the largest of the historical placer gold camps in the Tapajós
region of northern Brazil, having yielded an estimated 2M oz of gold from the overall 20-30M oz gold produced during the
Tapajós gold rush. Placer workings cover over 850ha on the property but are largely exhausted. The few remaining artisanal
workers now process gold from palaeo-valley placer deposits and in places exploit high-grade gold mineralization from quartz
veins in saprolite (shallow highly weathered bedrock).
Cabral reported an updated NI 43-101 Mineral Resource Estimate in December 2018
totalling 5.9M tonnes grading 0.9 g/t Au
(Indicated) and 19.5M tonnes grading 1.2 g/t Au (Inferred), or 0.2M ounces and 0.8M ounces of gold, respectively. That estimate
was based on four deposits drilled prior to the cessation of exploration in 2012.
FOR FURTHER INFORMATION PLEASE CONTACT:
Alan Carter
President and Chief Executive Officer
Cabral Gold Inc.
Tel: 604.676.5660
Email:
www.cabralgold.com
Dr. Adrian McArthur, B.Sc. Hons, PhD. FAusIMM., a consultant to the Company as well as a Qualified Person as defined by
National Instrument 43-101, supervised the preparation of the technical information in this news release.
Neither the TSX Venture Exchange nor its Regulation Services Provider (as such term is defined in the policies of the TSX
Venture Exchange) accepts responsibility for the adequacy or accuracy of this release.
Forward-looking Statements
This news release contains certain forward-looking information and forward-looking statements within the meaning of applicable
securities legislation (collectively "forward-looking statements").
The use of the words "will", "expected" and similar expressions
are intended to identify forward-looking statements.
These statements involve known and unknown risks, uncertainties and other
factors that may cause actual results or events to differ materially from those anticipated in such forward-looking statements.
Such forward-looking statements should not be unduly relied upon.
This news release contains forward-looking statements and
assumptions pertaining to the following:
strategic plans and future operations, and results of exploration.
Actual results achieved
may vary from the information provided herein as a result of numerous known and unknown risks and uncertainties and other
factors.
The Company believes the expectations reflected in those forward-looking statements are reasonable, but no assurance
can be given that these expectations will prove to be correct.
Notes
Gold analysis has been conducted by SGS method FAA505 (fire assay of 50g charge), with higher grade samples checked
by FAA525. Analytical quality is monitored by certified references and blanks. Until dispatch, samples are stored under the
supervision the Company's exploration office. The samples are couriered to the assay laboratory using a commercial
contractor. Pulps are returned to the Company and archived. Earlier channel sampling completed ahead of the drilling
campaign was conducted using a hand-trenching tool over exposed faces to maintain a consistent sample. The high-grade
Machichie sample was collected in run-of-mine stockpiles from the artisanal processing operation. Drill holes results are
quoted as down-hole length weighted intersections.
Under the agreement with the
Cuiú Cuiú condominium, local artisanal operators can process mineralization to a depth of
30m, unless otherwise negotiated. Shafts generally stop at or above the depth of the water-table.
[1]
Micon NI 43-101 amended resource estimate dated December 19, 2018.
To view the source version of this press release, please visit
https://www.newsfilecorp.com/release/43114