Alamos Gold Continues to Expand High-Grade Mineralization Between Eastern and Main Extensions at Island Gold
Alamos Gold Continues to Expand High-Grade Mineralization Between Eastern
and Main Extensions at Island Gold
TORONTO, Sept. 11, 2019 -- Alamos Gold Inc. (TSX:AGI; NYSE:AGI) (“Alamos” or the “Company”) today reported new
results from surface and underground exploration drilling at the Island Gold Mine, further extending high-grade gold
mineralization. All reported drill widths are true width of the mineralized zones, unless otherwise stated.
• Extending Mineralization in New Area of Focus: high-grade mineralization extended 85 metres (“m”) west
and 75 m below the nearest previously reported intersection (MH18-04) in the new area of focus between the
Eastern and Main Extensions. All nine holes drilled to date in this previously untested area have intersected
the E1E Zone including eight intersecting ore grade gold mineralization over a lateral extent of 300 m. This
area is located within a 500 m gap between Inferred Mineral Resource blocks, and is only 1,000 m from surface and
relatively close to existing infrastructure. New highlights include:
• 34.28 g/t Au (24.95 g/t cut) over 8.36 m (MH19-01); and
• 12.30 g/t Au (12.30 g/t cut) over 6.67 m (MH19-02).
• Main Extension Down-Plunge: high-grade mineralization extended 50 m east from the nearest previously
reported intersection (MH17-06) and 90 m from existing Mineral Resources . High-grade mineralization has been
extended over 1,000 m east of current mine workings and remains open along strike to the east and both up- and down-
plunge.
• 16.61 g/t Au (14.48 g/t cut) over 7.27 m (MH17-07).
• Main Extension Near Mine: high-grade mineralization intersected east of Mineral Reserves, and above
Inferred Resources from the 840-level exploration drift. New highlights include:
• 63.94 g/t Au (22.24 g/t cut) over 12.33 m (840-554-14); and
• 27.82 g/t Au (20.71 g/t cut) over 7.60 m (840-554-07).
Note: Drillhole composite intervals reported as “cut” may include higher grade samples which have been cut to 225 g/t Au for
Main and Extension 1 areas, and 160 g/t Au for Extension 2 Area.
“Ongoing exploration success at Island Gold continues to support further growth of the deposit and operation. We have
extended high-grade mineralization between the Main and Eastern Extensions and see excellent potential to add high-grade
Mineral Resources in this new area. This area is close to existing underground infrastructure including the 840 level exploration
drift which will allow us to further define its potential from underground and bring it into the mine plan relatively quickly,” said
John A. McCluskey, President and Chief Executive Officer.
2019 Drilling Program – Island Gold Mine
The focus of the 2019 exploration drilling program is to continue to expand the down-plunge and lateral extensions of the Island
Gold deposit with the objective of adding new near mine Mineral Resources across the two-kilometre long Island Gold Main
Zone (Figure 1).
The ongoing exploration program at Island Gold has been successful in extending high grade gold mineralization across each
of the Main, Western, and Eastern Extensions. This has translated into significant growth in Mineral Reserves and Resources
since the November 2017 acquisition of Island Gold.
A total of 28,123 m of surface directional and 18,676 m of underground exploration drilling has been completed as of August
31, 2019. New highlight intercepts can be found in Figures 1, 2, and 3 and Tables 1 and 2 at the end of this news release.
The 2019 exploration program at Island Gold includes 48,000 m of surface directional exploration drilling, 30,000 m of
underground exploration drilling, and 917 m of exploration drift development.
Surface Exploration Drilling
New Area of Focus between the Eastern and Main Extensions
Surface directional drilling remains focused on testing the new area of high-grade gold mineralization within the E1E Zone that
was discovered in May 2019. This area is located down-plunge from known Inferred Resource blocks, between the 850 m and
1,150 m vertical depths, and previously reported high-grade intersections approximately 350 m further to the east (Figure 2).
New highlights from the surface drilling program include (E1E-Zone) (Table 1):
• 34.28 g/t Au (24.95 g/t cut) over 8.36 m (MH19-01);
• 12.30 g/t Au (12.30 g/t cut) over 6.67 m (MH19-02); and
• 6.31 g/t Au (6.31 g/t cut) over 8.10 m (MH18-07).
All nine holes drilled to date in this area have intersected the E1E Zone with eight of the holes presenting ore
grade gold mineralization (see Figure 4). This includes new drill holes MH19-01, which intersected 34.28 g/t Au (24.95 g/t
cut) over 8.36 m, and MH19-02 which intersected 12.30 g/t Au (12.30 g/t cut) over 6.67 m. These new intersections are
located 75 m below and 85 m west of previously reported drill hole MH18-04 which intersected 31.66 g/t Au (31.66 g/t cut) over
2.95 m (see Press Release dated June 10, 2019).
These new drill hole intersections are approximately 225 m down-plunge from Inferred Mineral Resources in the Eastern
Extension, and 240 m vertically above Inferred Mineral Resources defined in the eastern down-plunge extent of the Main
Extension. Testing the continuity of high-grade mineralization between the Eastern and Main Extensions will be an ongoing
focus for the balance of 2019. Three surface directional diamond drill rigs are active in this area, and will continue with 75 to
100 m spaced step-out drilling. The 840 level exploration will be extended above this area by the end of 2019 providing
underground access to infill drill this area in 2020 while continuing to target further high-grade mineralization.
Main Extension
Surface directional drilling continues to extend gold mineralization with drill hole spacing ranging from 50 to 100 m (Figure 2).
New highlights from the surface drilling program include (E1E-Zone) (Table 1):
• 16.61 g/t Au (14.48 g/t cut) over 7.27 m (MH17-07);
• 5.98 g/t Au (5.98 g/t cut) over 5.24 m (MH14-7);
• 3.21 g/t Au (3.21 g/t cut) over 4.83 m (MH13-8); and
• 2.36 g/t Au (2.36 g/t cut) over 9.41 m (MH18-06).
New drillhole MH17-07 (16.61 g/t Au (14.48 g/t cut) over 7.27 m) extended high-grade gold mineralization 50 m east from the
nearest previously reported drill hole intersection from MH17-06 (24.08 g/t Au (14.21 g/t cut) over 6.27 m). Gold mineralization
continues to be expanded to the east, over one kilometre from existing mine workings. This east plunging high-grade ore shoot
remains open laterally, up- and down-plunge.
Two surface directional diamond drill rigs remain active in the Main Extension target area, focused on further extending high-
grade mineralization and defining additional Mineral Resources.
Drilling completed over the past few months in the eastern part of the Island Gold mine (Main Extension area, new area of
focus and Eastern Extension area) has confirmed the continuity of the E1E gold zone at depth. This zone now extends from
300 m to a vertical depth of more than 1400 m.
Underground Exploration Drilling
Underground exploration drilling is being conducted from the 340, 620 and 840 level exploration drifts. Drilling from the 340-
level exploration drift is testing an area to the east of the Mineral Reserve and Mineral Resource blocks of the Eastern
Extension, between 300 m and 500 m vertical depths. Drilling from the 620-level exploration drift tested an area between the
Main Mine and the Eastern Extension Mineral Reserve and Mineral Resource blocks, between 450 m and 750 m vertical
depths. Drilling from the 840-level exploration drift is testing the area between 840 m and 1000 m vertical depths to the east of
the existing Mineral Reserves, and above the Inferred Resource of the Main Extension.
New highlights from the underground exploration drilling program in the E1E Zone include (Figure 3, Table 2):
• 63.94 g/t Au (22.24 g/t cut) over 12.33 m (840-554-14);
• 27.82 g/t Au (20.71 g/t cut) over 7.60 m (840-554-07);
• 8.47 g/t Au (8.47 g/t cut) over 3.95 m (840-548-19);
• 9.58 g/t Au (9.58 g/t cut) over 4.30 m (620-568-47);
• 13.48 g/t Au (13.48 g/t cut) over 2.09 m (340-602-06);
• 11.12 g/t Au (11.12 g/t cut) over 2.19 m (340-602-14);
• 11.78 g/t Au (11.78 g/t cut) over 2.38 m (340-602-16); and
• 5.24 g/t Au (5.24 g/t cut) over 6.21 m (340-602-17).
New drillholes 840-554-14 (63.94 g/t Au (22.24 g/t cut) over 12.33 m ) and 840-554-07 (27.82 g/t Au (20.71 g/t cut) over 7.60
m) extended high-grade mineralization 150 m east of existing Mineral Reserves, above Inferred Mineral Resources in the Main
Extension. Two underground rigs remain active in the area focused on further defining this area with the objective of adding
near mine Mineral Resources.
Other Zones
The Island Gold Deposit consists of a number of subparallel mineralized zones, with the majority of Mineral Reserves and
Resources being defined in the C Zone and E1E Zone which constitutes the main production horizons at the Island Gold
mine.
Highlights of new intersections from underground exploration drilling of parallel zones and zones in which the lateral continuity
is not yet established (“Unknown Zone”) include (reported composite intervals are core lengths) (Table 2):
• 98.60 g/t Au (77.13 g/t cut) over 3.25 m (340-602-14);
• 29.81 g/t Au (29.81 g/t cut) over 5.75 m (740-465-56);
• 48.85 g/t Au (42.90 g/t cut) over 3.00 m (340-602-06);
• 12.89 g/t Au (12.89 g/t cut) over 5.95 m (340-602-06); and
• 13.92 g/t Au (13.92 g/t cut) over 4.10 m (340-602-12).
Qualified Persons
Chris Bostwick, FAusIMM, Alamos Gold’s Vice President, Technical Services, has reviewed and approved the scientific and
technical information contained in this news release. Chris Bostwick is a Qualified Person within the meaning of Canadian
Securities Administrator’s National Instrument 43-101 (“NI 43-101”).
Exploration programs at the Island Gold Mine are directed by Raynald Vincent, P.Eng., M.G.P., Chief Geologist at the Island
Gold Mine and a Qualified Person within the meaning of NI 43-101.
Quality Control
Assays for the surface exploration drilling program were completed at LabExpert in Rouyn-Noranda, Quebec. The Corporation
inserts at regular intervals quality control (QC) samples (blanks and reference materials) to monitor laboratory performance.
Cross check assays are done on a regular basis in a second accredited laboratory. The Quality Assurance / Quality Control
procedures are more completely described in the Technical Report filed on SEDAR by Richmont Mines, July 13, 2017.
About Alamos
Alamos is a Canadian-based intermediate gold producer with diversified production from four operating mines in North America.
This includes the Young-Davidson and Island Gold mines in northern Ontario, Canada and the Mulatos and El Chanate mines
in Sonora State, Mexico. Additionally, the Company has a significant portfolio of development stage projects in Canada,
Mexico, Turkey, and the United States. Alamos employs more than 1,700 people and is committed to the highest standards
of sustainable development. The Company’s shares are traded on the TSX and NYSE under the symbol “AGI”.
FOR FURTHER INFORMATION, PLEASE CONTACT:
Scott K. Parsons
Vice President, Investor Relations
(416) 368-9932 x 5439
All amounts are in United States dollars, unless otherwise stated.
The TSX and NYSE have not reviewed and do not accept responsibility for the adequacy or accuracy of this release.
Cautionary Note
This news release includes certain statements that constitute forward-looking information within the meaning of applicable
Canadian and U.S. securities laws ("forward-looking statements"). All statements in this news release, other than statements
of historical fact, which address events, results, outcomes or developments that Alamos expects to occur are forward-looking
statements. Forward-looking statements are generally, but not always, identified by the use of forward-looking terminology
such as “continue”, "expect", “believe", "anticipate", "plan", “forecast”, "estimate", "intend", “budget” or “potential” or variations
of such words and phrases and similar expressions or statements that certain actions, events or results "may", "could",
"would", "might" or "will" be taken, occur or be achieved or the negative connotation of such terms. Forward-looking
statements in this news release include statements with respect to planned exploration programs, the estimation of mineral
resources, exploration results, potential mineralization, changes in Mineral Resources and Proven and Probable Mineral
Reserves,and other information that is based on forecasts and projections of future operational, geological or financial results,
estimates of amounts not yet determinable and assumptions of management.
Exploration results that include geophysics, sampling, and drill results on wide spacings may not be indicative of the
occurrence of a mineral deposit. Such results do not provide assurance that further work will establish sufficient grade,
continuity, metallurgical characteristics and economic potential to be classed as a category of Mineral Resource. A Mineral
Resource that is classified as "Inferred" or "Indicated" has a great amount of uncertainty as to its existence and economic and
legal feasibility. It cannot be assumed that any or part of an "Indicated Mineral Resource" or "Inferred Mineral Resource" will
ever be upgraded to a higher category of Mineral Resource. Investors are cautioned not to assume that all or any part of
mineral deposits in these categories will ever be converted into Proven and Probable Mineral Reserves.
Alamos cautions readers not to place undue reliance on the forward-looking statements which are not guarantees of future
events as a number of factors could cause results, conditions, actions or events to differ materially from the targets, outlooks,
expectations, goals, estimates or intentions expressed in the forward-looking statements. These factors include, but are not
limited to: risks related to obtaining and maintaining necessary permits, licenses and authorizations required to carry out
planned exploration or development work, the actual results of current exploration activities, conclusions of economic and
geological evaluations, changes in project parameters as plans continue to be refined, employee and community relations,the
speculative nature of mineral exploration and development, contests over title to properties, changes in national and local
government legislation, control and regulations and and fluctuations of the price of gold and foreign exchange rates as well as
those factors discussed in the section entitled "Risk Factors" in Alamos' latest Annual Information Form and MD&A, each
under the heading “Risk Factors”, available on the SEDAR website at www.sedar.com or on EDGAR at www.sec.gov. The
foregoing should be reviewed in conjunction with the information found in this news release. The Company disclaims any
intention or obligation to update or revise any forward-looking statement, whether written or oral, or whether as a result of new
information, future events or otherwise, except as required by applicable law.
All of the forward-looking statements made in this news release are qualified by these cautionary statements.
Cautionary Note to U.S. Investors – Mineral Reserve and Resource Estimates
All Mineral Resource and Reserve estimates included in this news release or documents referenced in this news release have
been prepared in accordance with Canadian National Instrument 43-101 - Standards of Disclosure for Mineral Projects ("NI 43-
101") and the Canadian Institute of Mining, Metallurgy and Petroleum (the "CIM") - CIM Definition Standards on Mineral
Resources and Mineral Reserves, adopted by the CIM Council, as amended (the "CIM Standards"). NI 43-101 is a rule
developed by the Canadian Securities Administrators, which established standards for all public disclosure an issuer makes of
scientific and technical information concerning mineral projects. The terms "Mineral Reserve", "Proven Mineral Reserve" and
"Probable Mineral Reserve" are Canadian mining terms as defined in accordance with NI 43-101 and the CIM Standards.
These definitions differ materially from the definitions in the Securities Exchange Commission (the “SEC”) Industry Guide 7
("SEC Industry Guide 7") under the United States Securities Act of 1933, as amended, and the Exchange Act . Under SEC
Industry Guide 7 standards, a "final" or "bankable" feasibility study is required to report reserves, the three-year historical
average price is used in any reserve or cash flow analysis to designate reserves and the primary environmental analysis or
report must be filed with the appropriate governmental authority.
In addition, the terms "Mineral Resource", "Measured Mineral Resource", "Indicated Mineral Resource" and "Inferred Mineral
Resource" are defined in and required to be disclosed by NI 43-101 and the CIM Standards; however, these terms are not
defined terms under SEC Industry Guide 7 and are normally not permitted to be used in reports and registration statements
filed with the SEC. Investors are cautioned not to assume that all or any part of mineral deposits in these categories will ever
be converted into Mineral Reserves. "Inferred Mineral Resources" have a great amount of uncertainty as to their existence, and
great uncertainty as to their economic and legal feasibility. It cannot be assumed that all or any part of an Inferred Mineral
Resource will ever be upgraded to a higher category. Under Canadian rules, estimates of Inferred Mineral Resources may not
form the basis of feasibility or pre-feasibility studies, except in very limited circumstances. Investors are cautioned not to
assume that all or any part of an Inferred Mineral Resource exists or is economically or legally mineable. Disclosure of
"contained ounces" in a Mineral Resource is permitted disclosure under Canadian regulations; however, the SEC normally
only permits issuers to report mineralization that does not constitute "reserves" by SEC standards as in place tonnage and
grade without reference to unit measures.
Table 1: Island Gold – Previously Unreleased Select Composite Intervals from Surface Exploration Drilling
Composite intervals greater than 3 g/t Au weighted average, capping values:
Main Island and Extension 1 areas @ 225 g/t Au; Extension 2 Area @ 160 g/t Au.
Hole ID Zone Target Area From
(m) To (m)
Core
Length
(m)
True
Width
(m)
Au Uncut
(g/t)
Au Cut
(g/t)
Vertical
Depth
(m)
MH13-8 E1E Eastern Ext 1551.40 1556.70 5.30 4.83 3.21 3.21 1237
MH14-7 E1E Main Ext 1548.90 1555.70 6.80 5.24 5.98 5.98 1481
MH17-07 E1E Main Ext 1500.30 1507.80 7.50 7.27 16.61 14.48 1252
MH18-07 E1E Eastern Ext 1130.60 1140.40 9.80 8.10 6.31 6.31 1010
MH19-01 E1E Eastern Ext 1179.90 1191.00 11.10 8.36 34.28 24.95 1084
MH19-02 E1E Eastern Ext 1161.00 1168.60 7.60 6.67 12.30 12.30 1056
Note: Unknown zone corresponds to gold intercepts outside known ore zones and for which continuity is not yet established
and therefore true width has not been calculated.
Table 2: Island Gold – Previously Unreleased Select Composite Intervals from Underground Exploration Drilling
Composite intervals greater than 3 g/t Au weighted average, capping values:
Main Island and Extension 1 areas @ 225 g/t Au; Extension 2 Area @ 160 g/t Au.
Hole ID Zone Target Area From (m) To (m)
Core
Length
(m)
True
Width
(m)
Au
Uncut
(g/t)
Au
Cut
(g/t)
Vertical
Depth
(m)
340-602-06 E1E Eastern Ext 160.00 164.10 4.10 2.09 13.48 13.48 405
340-602-07 E1E Eastern Ext 125.35 128.40 3.05 2.19 7.59 7.59 365
340-602-14 E1E Eastern Ext 175.50 180.50 5.00 2.19 11.12 11.12 415
340-602-15 E1E Eastern Ext 132.50 136.30 3.80 2.27 3.87 3.87 366
340-602-16 E1E Eastern Ext 101.70 104.80 3.10 2.38 11.78 11.78 326
340-602-17 E1E Eastern Ext 91.35 98.40 7.05 6.21 5.24 5.24 285
620-543-73 E1E Eastern Ext 216.85 219.80 2.95 2.05 8.02 8.02 716
620-550-45 E1E Eastern Ext 249.70 253.30 3.60 2.22 5.43 5.43 718
620-568-28 E1E Eastern Ext 163.80 166.50 2.70 2.14 3.08 3.08 632
620-568-32 E1E Eastern Ext 178.20 180.60 2.40 2.04 4.48 4.48 656
620-568-33 E1E Eastern Ext 224.30 228.95 4.65 3.02 5.23 5.23 717
620-568-39 E1E Eastern Ext 203.00 207.60 4.60 3.21 3.17 3.17 690
620-568-42 E1E Eastern Ext 144.00 146.90 2.90 2.22 3.00 3.00 461
620-568-43 E1E Eastern Ext 102.60 105.70 3.10 2.87 4.50 4.50 583
620-568-44 E1E Eastern Ext 102.60 105.60 3.00 2.83 4.37 4.37 564
620-568-45A E1E Eastern Ext 110.50 114.40 3.90 3.43 4.81 4.81 515
620-568-46 E1E Eastern Ext 119.90 122.90 3.00 2.49 4.06 4.06 494
620-568-47 E1E Eastern Ext 108.70 113.70 5.00 4.30 9.58 9.58 530
840-548-19 E1E Main Ext 200.30 206.00 5.70 3.95 8.47 8.47 927
840-548-22 E1E Main Ext 174.00 177.20 3.20 2.80 5.48 5.48 890
840-548-29 E1E Main Ext 156.30 158.80 2.50 2.18 3.87 3.87 826
840-554-07 E1E Main Ext 282.30 295.50 13.20 7.60 27.82 20.71 1049
840-554-14 E1E Main Ext 273.10 290.40 17.30 12.33 63.94 22.24 1038
840-560-01 E1E Main Ext 216.00 220.20 4.20 2.69 8.46 8.46 940
340-602-06 Unknown Eastern Ext 13.00 18.95 5.95 12.89 12.89 330
340-602-06 Unknown Eastern Ext 42.00 45.00 3.00 48.85 42.90 345
340-602-07 Unknown Eastern Ext 71.58 74.35 2.77 4.08 4.08 347
340-602-08 Unknown Eastern Ext 60.00 62.70 2.70 6.53 6.53 325
340-602-12 Unknown Eastern Ext 66.40 70.50 4.10 13.92 13.92 335
340-602-14 Unknown Eastern Ext 48.00 51.25 3.25 98.60 77.13 348
740-465-56 Unknown Western Ext 154.65 160.40 5.75 29.81 29.81 712
840-548-22 Unknown Main Ext 105.85 108.50 2.65 7.02 7.02 873
840-554-08 Unknown Main Ext 20.70 23.17 2.47 5.29 5.29 841
840-554-09 Unknown Main Ext 60.00 63.00 3.00 3.83 3.83 855
840-554-12 Unknown Main Ext 156.00 162.50 6.50 3.21 3.21 937
Note: Unknown zone corresponds to gold intercepts outside known ore zones and for which continuity is not yet established
and therefore true width has not been calculated.
Table 3: Surface exploration drill holes; azimuth, dip, drilled length, and collar location at surface (UTM NAD83).
Hole ID Azimuth
(°) Dip (°)
Drilled
Length
(m)
UTM
Easting
(m)
UTM
Northing
(m)
UTM
Elevation
(m)
Comments
MH13-7 337 -72 811 692074 5351046 389 Cut from MH13 at 859m
MH13-8 337 -72 630 692074 5351046 389 Cut from MH13-7 at 1028m
MH14-7 338 -85 572 691522 5351123 394 Cut from MH14-6 at 1133m
MH16-07 337 -73 907 691002 5350845 387 Cut from MH16-06 at 721m
MH17-07 334 -73 585 692320 5351076 395 Cut from MH17-06 at 1076m
MH17-08 334 -73 184 692320 5351076 395 Abandoned
MH18-06 339 -75 738 691886 5351456 395 Cut from MH18-05 at 586m
MH18-07 339 -75 834 691886 5351456 395 Cut from MH18-05 at 566m
MH19-01 336 -79 1342 691646 5351376 399
MH19-02 336 -79 644 691646 5351376 399 Cut from MH19-01 at 735m
Note: UTM mine surface elevation 382 m
Table 4: Underground exploration drill holes; azimuth, dip, drilled length, and collar location at surface (UTM
NAD83).
Hole ID Azimuth
(°)
Dip
(°)
Drilled
Length (m)
UTM Easting
(m)
UTM Northing
(m)
UTM
Elevation (m)
340-594-10 140 25 90 691394 5352153 75
340-594-11 112 37 108 691395 5352154 76
340-602-06 158 -34 222 691454 5352213 61
340-602-07 158 -22 159 691454 5352213 61
340-602-08 158 -5 123 691454 5352213 62
340-602-09 158 23 105 691454 5352213 63
340-602-10 150 -37 246 691454 5352213 61
340-602-11 150 -29 177 691454 5352213 61
340-602-12 148 -14 135 691454 5352213 61
340-602-13 146 10 111 691454 5352213 62
340-602-14 141 -33 243 691454 5352213 60
340-602-15 139 -21 153 691455 5352213 61
340-602-16 136 -4 126 691454 5352213 62
340-602-17 131 22 120 691455 5352213 63
620-543-73 153 -30 240 690967 5351872 -226
620-543-76 147 -18 224 690967 5351872 -226
620-550-38 148 -7 204 691020 5351907 -225
620-550-45 137 -27 291 691020 5351907 -225
620-568-25 176 61 159 691194 5351960 -217
620-568-26 172 46 132 691194 5351960 -217
620-568-27 170 -4 180 691194 5351960 -217
620-568-28 170 -12 192 691192 5351959 -219
620-568-29 168 -28 240 691194 5351960 -217
620-568-30 166 -1 171 691194 5351960 -217
620-568-31 163 -16 198 691193 5351959 -219
620-568-32 163 -21 219 691193 5351959 -219
620-568-33 163 -32 264 691193 5351959 -219
620-568-36 157 -23 225 691193 5351959 -219
620-568-37 157 -29 240 691193 5351959 -219
620-568-38 153 -35 294 691193 5351959 -219
620-568-39 150 -27 240 691193 5351959 -219
620-568-40 145 69 159 691192 5351961 -215
620-568-41 169 -19 222 691193 5351959 -219
620-568-42 194 70 192 691192 5351961 -215
620-568-43 157 9 126 691193 5351959 -218
620-568-44 146 19 123 691193 5351959 -217
620-568-45A 141 50 129 691194 5351960 -217
620-568-46 141 60 141 691193 5351961 -215
620-568-47 131 37 129 691194 5351960 -216
740-465-56 158 16 267 690236 5351584 -374
840-548-19 151 -23 240 691029 5351853 -464
840-548-21 149 21 210 691029 5351853 -464
840-548-22 166 -15 189 691028 5351852 -464
840-548-29 148 7 196 691029 5351853 -464
840-554-07 156 -44 333 691083 5351880 -464
840-554-08 152 9 198 691082 5351879 -463
840-554-09 150 -11 219 691082 5351879 -462
840-554-10 150 -22 243 691082 5351879 -463
840-554-11 150 -30 270 691082 5351879 -463
840-554-12 148 -35 288 691082 5351879 -463
840-554-13 148 -40 315 691082 5351879 -464
840-554-14 148 -44 354 691082 5351879 -464
840-560-01 159 -27 249 691139 5351903 -462
Note: UTM mine surface elevation 382 m
Photo accompanying this announcement are available at
https://www.globenewswire.com/NewsRoom/AttachmentNg/3eb720c6-ba60-4311-a790-d69ac79c807c
https://www.globenewswire.com/NewsRoom/AttachmentNg/9bca3697-aaad-4f4f-8960-3f25d6385536
https://www.globenewswire.com/NewsRoom/AttachmentNg/3285eb34-873d-494b-a976-bb1e3f1ecfe5
https://www.globenewswire.com/NewsRoom/AttachmentNg/c5aa6357-7e75-4536-ac92-0115d78ec88b